Refrigeration condensers presentation. Types of capacitors. Variable capacitor

"Alternating Current" - Definition. Alternating current is an electric current that changes over time in magnitude and direction. Alternating current. Alternator. EZ 25.1 Producing alternating current by rotating a coil in a magnetic field.

“The action of electric current” - You need to make an accurate cast of some wooden relief. How can we judge the amount of electricity passed by the chemical effect of current? What effects of electric current occur in your apartment? "Let's think about it." Select equipment for the experiment on the demonstration table in accordance with the picture.

“Electric current power” - A. A=IU B. P=UI C. I=U/R A. A=UI B. P=UI B. A=UIt A. W B. A C. B A. 100 W B. 400 W B. 4 kW. The effect of current is characterized by two quantities. Voltage... Current work A=UIt. Electric current... Current strength... The power of an electric iron is 600 W, and the power of a TV is 100 W. Know the definition of the work and power of electric current in a section of a circuit?

“Electrical capacity and capacitors” - Parallel. Capacitors. Variable capacitor. The entire electric field is concentrated inside the capacitor. -q. Energy of a charged capacitor. Connection of capacitors. Electrical capacity. Consistent. Designation on electrical diagrams: Fixed capacitor. +q. Derivation of the formula for the energy of a charged capacitor.

"Alternating electric current" - The result is the average power over a period. Alternating Electric Current. The instantaneous current value is directly proportional to the instantaneous voltage value. E=-ф’= -bs(cos ?t)’= = bs? * sin ?t = em sin ?t. Conversely, undamped forced oscillations are of great practical importance. U=Um cos?t.

"Capacitor physics" - - Paper capacitor - mica capacitor electrolytic capacitor. Purpose of capacitors. Capacitors. When connecting an electrolytic capacitor, polarity must be observed. Air condenser. Definition of a capacitor. Presentation in Physics on the Topic: Paper capacitor. The work was completed by: Regina Dautova.

There are 9 presentations in total

Description of the presentation by individual slides:

1 slide

Slide description:

MINISTRY OF EDUCATION AND SCIENCE OF THE RF GBPOU "Technological College named after. N.D. Kuznetsova" SPECIALTY INFORMATION SYSTEMS Presentation on physics on the topic: "Capacitors" Prepared by: 1st year student Victoria Sergeevna Vidyasova Scientific supervisor: Olga Vasilievna Kurochkina Samara, 2016.

2 slide

Slide description:

Introduction: Definition Types of capacitors Marking of capacitors Application of capacitors

3 slide

Slide description:

DEFINITION A capacitor is an electrical (electronic) component constructed from two conductors (plates) separated by a dielectric layer. There are many types of capacitors and they are mainly divided according to the material of the plates themselves and the type of dielectric used between them.

4 slide

Slide description:

Types of capacitors Paper and metal capacitors In a paper capacitor, the dielectric separating the foil plates is special capacitor paper. In electronics, paper capacitors can be used in both low-frequency and high-frequency circuits. Sealed metal-paper capacitors, which instead of foil (as in paper capacitors) use vacuum deposition of metal onto a paper dielectric, have good quality electrical insulation and increased specific capacitance. A paper capacitor does not have great mechanical strength, so its filling is placed in a metal case, which serves as the mechanical basis of its design.

5 slide

Slide description:

Electrolytic capacitors In electrolytic capacitors, unlike paper capacitors, the dielectric is a thin layer of metal oxide formed electrochemically on a positive cover of the same metal. The second cover is a liquid or dry electrolyte. The material that creates the metal electrode in an electrolytic capacitor can be, in particular, aluminum and tantalum. Traditionally, in technical jargon, “electrolyte” refers to aluminum capacitors with a liquid electrolyte. But, in fact, tantalum capacitors with solid electrolyte also belong to electrolytic capacitors (they are less common with liquid electrolyte). Almost all electrolytic capacitors are polarized, and therefore they can only operate in DC voltage circuits while maintaining polarity. In case of polarity reversal, an irreversible chemical reaction may occur inside the capacitor, leading to the destruction of the capacitor, even to its explosion due to the gas released inside it. Electrolytic capacitors also include the so-called supercapacitors (ionistors) with an electrical capacity that sometimes reaches several thousand Farads.

6 slide

Slide description:

Aluminum Electrolytic Capacitors Aluminum is used as the positive electrode. The dielectric is a thin layer of aluminum trioxide (Al2O3), Properties: they work correctly only at low frequencies have a large capacitance Characterized by a high capacitance-to-size ratio: electrolytic capacitors are usually large in size, but capacitors of a different type, the same capacitance and breakdown voltage would be much larger in size. They are characterized by high leakage currents and have moderately low resistance and inductance.

7 slide

Slide description:

Tantalum electrolytic capacitors This is a type of electrolytic capacitor in which the metal electrode is made of tantalum and the dielectric layer is made of tantalum pentoxide (Ta2O5). Properties: high resistance to external influences, compact size: for small ones (from several hundred microfarads), size comparable to or smaller than aluminum capacitors with the same maximum breakdown voltage, lower leakage current compared to aluminum capacitors.

8 slide

Slide description:

Polymer capacitors Unlike conventional electrolytic capacitors, modern solid-state capacitors have a polymer dielectric instead of an oxide film used as a plate separator. This type of capacitor is not subject to swelling and charge leakage. The physical properties of the polymer contribute to the fact that such capacitors have a high pulse current, low equivalent resistance and stable temperature coefficient even at low temperatures. Polymer capacitors can replace electrolytic or tantalum capacitors in many circuits, such as filters for switching power supplies, or in DC-DC converters.

Slide 9

Slide description:

Film capacitors In this type of capacitor, the dielectric is a plastic film, for example, polyester (KT, MKT, MFT), polypropylene (KP, MKP, MFP) or polycarbonate (KC, MKC). Electrodes can be deposited on this film (MKT, MKP, MKC) or made in the form of a separate metal foil, wound into a roll or pressed together with a dielectric film (KT, KP, KC). The modern material for capacitor film is polyphenylene sulfide (PPS). General properties of film capacitors (for all types of dielectrics): they work properly at high current have high tensile strength have a relatively small capacitance minimum leakage current used in resonant circuits and RC snubbers Individual types of film differ in: temperature properties (including with the sign temperature coefficient of capacity, which is negative for polypropylene and polystyrene, and positive for polyester and polycarbonate) maximum operating temperature (from 125 °C, for polyester and polycarbonate, up to 100 °C for polypropylene and 70 °C for polystyrene) resistance to electrical breakdown , and therefore the maximum voltage that can be applied to a certain film thickness without breakdown.

10 slide

Slide description:

Ceramic capacitors This type of capacitors is made in the form of one plate or a pack of plates from a special ceramic material. Metal electrodes are sprayed onto the plates and connected to the terminals of the capacitor. The ceramic materials used can have very different properties. The diversity includes, first of all, a wide range of relative electrical permeability values ​​(up to tens of thousands, and this value is found only in ceramic materials). Such a high permeability value allows the production of ceramic capacitors (multilayer) of small sizes, the capacitance of which can compete with the capacitance of electrolytic capacitors , and at the same time working with any polarization and characterized by less leakage. Ceramic materials are characterized by a complex and nonlinear dependence of parameters on temperature, frequency, and voltage. Due to the small size of the case - this type capacitors have special markings.

12 slide

Slide description:

How are large capacitors marked? To read correctly specifications device, some preparation is required. You need to start studying with units of measurement. To determine capacitance, a special unit is used - farad (F). The value of one farad for a standard circuit seems too large, so household capacitors are marked in smaller units. The most commonly used is mF = 1 µF (microfarad), which is 10-6 farads.

Slide 13

Slide description:

In calculations, an off-label unit can be used - millifarad (1mF), which has a value of 10-3 farads. In addition, designations can be in nanofarads (nF) equal to 10-9 F and picofarads (pF) equal to 10-12 F. Capacitance markings for large capacitors are applied directly to the housing. In some designs, the markings may differ, but in general, you need to be guided by the units of measurement mentioned above.

Slide 14

Slide description:

Designations are sometimes written in capital letters, for example, MF, which actually corresponds to mF - microfarads. The marking fd is also found - an abbreviated English word farad. Therefore mmfd will correspond to mmf or picofarad. In addition, there are designations that include a number and one letter. This marking looks like 400m and is used for small capacitors. In some cases, it is possible to apply tolerances, which are an acceptable deviation from the rated capacitance of the capacitor. This information is of great importance when, when assembling certain types of electrical circuits, capacitors with precise capacitance values ​​may be required. If we take the marking 6000uF + 50%/-70% as an example, then the maximum capacitance value will be 6000 + (6000 x 0.5) = 9000 uF, and the minimum 1800 uF = 6000 - (6000 x 0.7).

15 slide

Slide description:

If there are no percentages, you need to find the letter. Usually it is located separately or after the numeric designation of the container. Each letter corresponds to a specific tolerance value. After this, you can begin to determine the rated voltage. With large capacitor housing sizes, voltage markings are indicated by numbers followed by letters or letter combinations in the form V, VDC, WV or VDCW. The WV symbols correspond to the English phrase WorkingVoltage, which means operating voltage. Digital readings are considered to be the maximum permissible capacitor voltage, measured in volts.

16 slide

Slide description:

If there is no voltage marking on the device body, such a capacitor should only be used in low-voltage circuits. In an AC circuit, use a device designed specifically for this purpose. Capacitors designed for D.C., without the possibility of converting the rated voltage. The next step is to identify the positive and negative symbols that indicate the presence of polarity. Determining the positive and negative is of great importance, since incorrect determination of the poles can lead to a short circuit and even explosion of the capacitor. In the absence of special markings, the device can be connected to any terminals, regardless of polarity.

Slide 17

Slide description:

The pole designation is sometimes applied in the form of a colored stripe or a ring-shaped indentation. This marking corresponds to the negative contact in electrolytic aluminum capacitors, which are shaped like a tin can. In very small tantalum capacitors, these same symbols indicate positive contact. If there are plus and minus symbols, the color coding can be ignored. Other markings. The markings on the capacitor body allow you to determine the voltage value. The figure shows Special symbols, corresponding to the maximum permissible voltage for specific device. In this case, parameters are given for capacitors that can only be operated at constant current.

Slide 19

Slide description:

Application of capacitors. The energy of a capacitor is usually not very high - no more than hundreds of joules. In addition, it is not preserved due to the inevitable charge leakage. Therefore, charged capacitors cannot replace, for example, batteries as sources of electrical energy. Capacitors can store energy for a more or less long time, and when charged through a low-resistance circuit, they release energy almost instantly. This property is widely used in practice. A flash lamp used in photography is powered by the electric current of a capacitor discharge, which is pre-charged by a special battery. Excitation of quantum light sources – lasers – is carried out using a gas-discharge tube, the flash of which occurs when a bank of capacitors of large electrical capacity is discharged. However, capacitors are mainly used in radio engineering...

20 slide

Slide description:

“Capacitor physics” - Types of capacitors. - Paper capacitor - mica capacitor electrolytic capacitor. Air condenser. Capacitor connections. - Air condenser. Definition of a capacitor. When connecting an electrolytic capacitor, polarity must be observed. Purpose of capacitors.

“Using capacitors” - Experiments with a capacitor. The capacitor is used in ignition circuits. Energy formulas. Application of capacitors. Features of the use of capacitors. The capacitor is used in medicine. Lamps with discharge lamps. Capacitive keyboard. Capacitor. Cell phones. Used in telephony and telegraphy.

“Electrical capacity and capacitors” - In the computer keyboard. Variable capacitor. Connection of capacitors. Electrical capacity. Consistent. Flashlights. Capacitor connection diagrams. Designation on electrical diagrams: Capacitors. Electrical capacity of a flat capacitor. The entire electric field is concentrated inside the capacitor.

“Use of capacitors” - For the latter batteries, regeneration time is fundamentally important. Polymer capacitors with solid electrolyte on the chipset. Diagram of a telephone bug. Current rectifier circuit. Capacitor CTEALTG STC - 1001. Condenser microphone. A successful association is on the Sciencentral website. Studio condenser directional microphone for wide applications.

“Capacitor” - Capacity of the capacitor. Charge ratio. Capacitor energy. Variable capacitor. Paper capacitor. Square. Capacitor. Application of capacitors. Physics lesson in 9th grade

Slide 1

Types of capacitors and their applications.

Slide 2

A capacitor is a device for storing charge. One of the most common electrical components. There are many different types capacitors, which are classified according to various properties.

Slide 3

Basically, the types of capacitors are divided: According to the nature of the change in capacitance - constant capacitance, variable capacitance and tuning. According to the dielectric material - air, metallized paper, mica, Teflon, polycarbonate, oxide dielectric (electrolyte). According to the installation method - for printed or mounted mounting.

Slide 4

Ceramic capacitors.

Ceramic capacitors or ceramic disk capacitors are made of a small ceramic disk coated on both sides with a conductor (usually silver). Due to their fairly high relative dielectric constant (6 to 12), ceramic capacitors can accommodate quite a large capacitance in a relatively small physical size.

Slide 5

Film capacitors.

The capacitance of the capacitor depends on the area of ​​the plates. In order to compactly accommodate a large area, film capacitors are used. The principle of “multi-layering” is used here. Those. create many layers of dielectric, alternating layers of plates. However, from an electrical point of view, these are the same two conductors separated by a dielectric, like a flat ceramic capacitor.

Slide 6

Electrolytic capacitors.

Electrolytic capacitors are usually used when large capacitance is required. The design of this type of capacitor is similar to that of film capacitors, only here instead of a dielectric, special paper impregnated with electrolyte is used. The capacitor plates are made of aluminum or tantalum.

Slide 7

Tantalum capacitors.

Tantalum capacitors are physically smaller than their aluminum counterparts. In addition, the electrolytic properties of tantalum oxide are better than aluminum oxide - tantalum capacitors have significantly less current leakage and higher capacitance stability. The range of typical capacitances is from 47nF to 1500uF. Tantalum electrolytic capacitors are also polar, but they tolerate incorrect polarity connections better than their aluminum counterparts. However, the range of typical voltages for tantalum components is much lower - from 1V to 125V.

Slide 8

Variable capacitors.

Variable capacitors are widely used in devices that often require adjustment during operation - receivers, transmitters, measuring instruments, signal generators, audio and video equipment. Changing the capacitance of the capacitor allows you to influence the characteristics of the signal passing through it.

Slide 9

Trimmer capacitors.

Trimmer capacitors are used for one-time or periodic capacitance adjustment, in contrast to “standard” variable capacitors, where the capacitance changes in “real time”. This adjustment is intended for the equipment manufacturers themselves, and not for its users, and is performed with a special adjusting screwdriver. A regular steel screwdriver is not suitable as it may affect the capacitance of the capacitor. The capacity of tuning capacitors is usually small - up to 500 picoFarads.

Slide 10

Application of capacitors.

An important property of a capacitor in an alternating current circuit is its ability to act as capacitive reactance (inductive in the coil). If you connect a capacitor and a light bulb in series to a battery, it will not light up. But if you connect it to an AC source, it will light up. And the higher the capacitance of the capacitor, the brighter it will glow. Due to this property, they are widely used as a filter, which can quite successfully suppress HF and LF interference, voltage ripple and AC surges.

Slide 11

Due to the ability of capacitors to accumulate charge for a long time and then quickly discharge in a circuit with low resistance to create a pulse, it makes them indispensable in the production of photo flashes, electromagnetic-type accelerators, lasers, etc. Capacitors are used when connecting a 380 to 220 Volt electric motor. It is connected to the third terminal, and due to the fact that it shifts the phase by 90 degrees on the third terminal, it becomes possible to use a three-phase motor in a single-phase 220 Volt network. In industry, capacitor units are used to compensate reactive energy.

Slide 12

The ability of a capacitor to accumulate and store electric charge for a long time, made it possible to use it in elements for storing information. And also as a power source for low-power devices. For example, an electrician's probe, which you just need to insert into a socket for a couple of seconds until the built-in capacitor is charged, and then you can ring circuits with it all day long. But unfortunately, the capacitor is significantly inferior in its ability to store electricity battery due to leakage currents (self-discharge) and the inability to accumulate large amounts of electricity.