Asus rt n16 does not connect. Setting up and connecting ASUS RT-N16. Appearance and hardware components

Connection:

1. Insert the Internet cable into the blue port of the router. If you are using a connection not via a wire, but, for example, via a 3G modem, then this modem must be inserted into one of the USB ports.

2. Insert the patch cord (shorter cable included with the router) with one end into one of the yellow ports of the router, and the other end into the port of your computer or laptop.

3. The power supply also needs to be connected to both the router and the mains.

Internet setup:

1. Go to the router interface by entering 192.168.1.1 in the address bar, after which you must enter your login and password. By default they are installed: admin – admin.

2. When setting up the router for the first time, the “ Quick setup" You can configure the router this way by following the on-screen prompts. Or go to normal settings by clicking on the home page button (see figure below).

3. In the left menu, select “Internet”.

4. In the “WAN connection type” item, select the type of connection of your network, this information you can check with your provider.

5. When connecting with the “Automatic IP” type, you do not need to change anything in the settings. When selecting other connection types, credentials will be required, i.e. “Username” and “Password”, as well as for connections such as “PPTP”, “L2TP”, you will also need a “VPN server”. You can find out all this data in the contract, or in the technical information. support from your provider.

6. When all the data has been entered, click on “Apply”.

Setting up the Internet via a 3G/4G modem.

1. Select “USB – application” in the left menu.

3. In the window that opens, put a dot next to “Yes” in the “Enable USB Modem” section.

4. After, select the country, your provider in the “IPS” section, and also enter the dialed number, username and password. You can find out all this data in the documents that came with your modem, or simply by calling your service provider. support.

5. Having entered all the settings, click “Apply”. The Internet is configured, now let's configure it wireless connection.

Wi-Fi setup:

1. In the left menu, select “Wireless Network”.

2. In the window that opens, you need to fill in several fields. "SSID" is the name of your network, i.e. the name that will be displayed when connecting.

3. In the “Authentication Method” item, select “WPA2 - Personal”.

4. In the WPA Pre-Shared Key field, you need to enter a password that you will need to enter when connecting to your network.

5. The remaining fields do not need to be changed, so click on the “Apply” button.

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.1.1 in the address bar, Username - admin, Password - admin(provided that the router has factory settings and its IP has not changed).

Setting up Wi-Fi on the router

In the router interface, you need to go to the tab on the left Extra options, in the list that opens, select Wireless network.

We set the parameters as follows:

1. SSID field: enter the name wireless network. The value in this field cannot be changed.

2.Authentication method: WPA2-Personal

3.WPA encryption: TKIP or AES

4.WPA Preshared Key: You must enter any set of numbers from 8 to 63. They also need to be remembered so that you can specify them when connecting to the network.

5. Click the button below Apply

Setting up an Internet connection

In the router interface, you need to select the tab on the left Additional parameters, in the list that opens, select WAN.

Setting up a PPPoE connection

1. WAN connection type: PPPoE

2. Obtain WAN IP address automatically: Yes

3. Username: Your login according to the contract

4. Password: Your password according to the agreement

6. Save the settings with the Apply button.

Setting up an L2TP connection

1. WAN connection type - L2TP

4. Username and password - login and password from the agreement

5. VPN server- enter the IP address or name of the VPN server according to the contract

6. The remaining parameters can be left unchanged. In the hostname, write something in English. Save your settings.

Setting up PPTP(VPN) at automatic receipt local IP address

1. WAN connection type: PPTP

2. Enable WAN, Enable NAT, Enable UPnP - set YES everywhere

3. Get an IP address and connect to DNS automatically - put an end to YES

4. Username: Your login according to the contract

5. Password: Your password according to the agreement

6. Heart-Beat or PPTP/L2TP(VPN) server: enter the IP address or name of the VPN server according to the agreement

7. Save the settings with the Apply button.

Setting up PPTP (VPN) with a static local IP address

1. WAN connection type: PPTP

2. Obtain an IP address and connect to DNS automatically - set the dot to No

3. IP address: We enter your IP address according to the contract

4. Subnet mask: Enter the mask according to the agreement

5. Main gateway: We drive in the gateway according to the contract

6. DNS server 1: and DNS server 2: enter your provider’s servers (Rostelecom Omsk DNS 1: 195.162.32.5 DNS 2: 195.162.41.8)

7. Username: Your login according to the contract

8. Password: Your password according to the agreement

9. Heart-Beat or PPTP/L2TP(VPN) server: enter the IP address or name of the VPN server according to the contract

10. Save the settings with the Apply button.

NAT when automatically obtaining an IP address (DHCP)

1. WAN connection type: Dynamic IP

2. Save the settings with the Apply button

Checking Internet connection status

Saving/restoring router settings

After setting up, it is recommended to save them so that if problems arise, you can restore them. To do this you need to go to the tab Additional settings, Administration menu", tab "Restore/Save/Load settings.

To save the current router settings, click the Save button. The settings file will be saved to the specified location on your hard drive.

To restore settings settings from a file, you must click the Select file button, specify the path to the settings file, then click the Send button.

Attention! Clicking the Restore button will restore factory settings!

Source: rudevice.ru

So that bright day came when I finally had the opportunity to work on my Asus RT-N16 router. In fact, this is the same Asus WL-500gV2 (it differs only in the firmware), I would even say its older brother, so I think this post will be of interest to all owners of both routers.

To begin with, strictly speaking, a little about the price of the issue and the technical component:

Equipment:

— The Asus RT-N16 access point itself: $200

— Removable hard drive, for example Transcend 500gb: $75

— Any 8 Gb flash drive: $15

— External IP address with open ports without restrictions: on average, the cost of a normal channel in Moscow and the region with a dedicated IP is $20/month.

Total: on average, one-time costs are $300 and monthly costs are $20.

FURTHER SETUP MAKES SENSE ONLY IF ALL OF THE ABOVE ELEMENTS ARE PRESENT (with the possible exception of a flash drive, since movies and programs can be downloaded and put on a hard drive).

The main resource on this topic is this one:

Before you start doing anything, you need to download from the site:

Your current factory firmware (it is listed on the first page when logging into the router). Next, I recommend that you familiarize yourself with the recovery procedure; in the case of spruce, the point will go into the so-called emergency mode (this happened to me at a certain stage, but more on that later). So disaster recovery:

1 Download and unzip the firmware.

2 Install the Firmware Restoration utility from the included disk.

3 Configure your computer’s network settings (in TCP/IP properties):

manually use IP address 192.168.1.2 mask 255.255.255.0

4 Connect your computer with a cable to any of the LAN ports of the router.

5 Turn off the power on the router, press and hold the Restore button, turn on the power,

hold the button for 10-15 seconds until the indicator power supply will not start flashing continuously.

6 Run the Firmware Restoration utility, specify the path to the firmware and upload it to the router.

7 The screen should display the process of downloading the firmware to the router.

8 After downloading the firmware and rebooting the router, enter the menu http://192.168.1.1

Here we see that my current (factory) firmware is 1.0.1.9 (I downloaded the same one from the site to be sure, which I did not regret later). But we won’t need all this; we will need alternative firmware.

1 Alternative firmware.

a) download latest version firmware of Oleg’s followers (Oleg is probably some kind of mega-brain, since almost all alternative firmwares, which actually work from him) - “Enthusiasts” from here and unpack into any folder (you can see the log of firmware changes).

b) use the Restore button to reset the router to factory settings (hold for about 5 seconds, until the power indicator starts flashing - you can release the button)

c) with installation disk, which came with the router, install the ASUS RT-N16 utility and run the utility called Firmware restoration

d) unplug the router’s power supply wire, disconnect all wires (wan, usb, etc.) leave 1 patch cord (included with the router) plugged into 1 of the LAN connectors (Lan1-Lan4), from the other end into the computer from which we will stitch.

d) manually set the settings network connection computer IP 192.168.1.2, mask 255.255.255.0, gateway and dns 192.168.1.1 (gateway and dns are set incorrectly in the screenshot below)

e) hold down the “restore” button on the router without releasing it

insert the power, continue to hold it for about 5 seconds, the power indicator will start blinking, which means that the router is in recovery mode (ready to receive the firmware), release the button on the router.

g) in the Firmware restoration utility, select the unpacked firmware (at the time of writing, the latest r1699 is RT-N16-1.9.2.7-rtn-r1699.trx)

h) disable the built-in Windows firewall, antiviruses and other blocking programs, and click on the “Download (U)” button in the utility - the router will be searched, if everything is configured correctly, the download will begin software into the router’s flash memory, otherwise, if it says “No devices found in recovery mode,” there are several reasons:

— the IP address and/or mask is set incorrectly in network settings computer;

— the firewall (antivirus) blocks connections from the firmware program;

— the router is not in recovery mode;

— there is no network connection (the cable is broken) with the router, check the cable.

If it writes the error “Unable to create socket”, it means you have installed (running) a program like tftpd, or another that occupies the required port, which is used to transfer the firmware to the router.

The process of flashing the firmware and automatically rebooting the router lasts about 3 minutes. After the router boots up (the power and wi-fi indicators are lit), press the “restore” button again and hold for at least 5 seconds (10 seconds is enough) -

the power indicator will start flashing, then when you release the button, the router will begin initializing nvram - it will write the factory default settings and reboot (no more than 1 minute), now try to go to the browser address http://192.168.1.1 - a login window should appear and password – enter the login and password admin to enter the web interface for managing the router

and move on to the next section, otherwise we start over.

2. installation of the script from valerakvb

2.1. preliminary configuration of the router for working with scripts and programs

After visiting the router page with firmware from enthusiasts

a) go to the IP Config section and configure your Internet connection

save (all settings in the router are saved in the same way and applied to this firmware) as follows - first click Apply, then the Finish button

then after clicking the Finish button the following dialog will appear:

You must click Save&Restart - after this the router will apply the settings (in different cases it may reboot to apply the settings) usually no more than 20 seconds

b) changing the user name (for running programs)

go to the System setup tab, select Change name in the submenu, in the right window in 2 lines enter the new name root

press save, then go to some point where there is a finish button, in order to save the new name and apply it, for example in System setup – Services

A window with the Save&Restart button will appear again - click and wait for the settings to be applied. If everything goes correctly, the browser, after loading the router, will again ask you to enter the username and password to enter the router control panel - enter root, password admin, if everything is correct, the Routea page will open again, otherwise enter the password and login admin, and do point b again.

After that, go again to the System setup tab, select Change name in the submenu and look - the new name should be displayed in the top line - root. The password is changed in the same way (save, then finish and Save&Restart in any menu item, otherwise it will not be saved) on the System tab setup – Change Password (don’t forget to change the password, otherwise they may log in with the standard password and play tricks with your router).

This concludes my story for today.

To be continued…

Multifunctional wireless gigabit router 802.N. Powerful processor, high speed packet processing. Supports up to 300 thousand simultaneous sessions to support P2P clients. Availability in the router USB port 2.0 for connection peripheral devices opens up new possibilities of use: can be used to connect a network printer/MFP or external data storage to organize a file server. Updated Download Master: high download speed and maximum ease of use.

Instructions for setting up the Asus RT-N16 router

Authorization

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.1.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Setting up Wi-Fi on the router

In the router interface, you need to go to the tab on the left Extra options Wireless network.

We set the parameters as follows:

1. Field SSID: Enter the name of the wireless network. The value in this field cannot be changed.
2. Authentication method: WPA2-Personal
3. WPA encryption: TKIP or AES
4. WPA Preshared Key: you must enter any set of numbers from 8 to 63. They also need to be remembered so that you can specify them when connecting to the network.
5. Click the button below Apply

Setting up an Internet connection

In the router interface, you need to select the tab on the left Extra options, in the list that opens, select WAN.

Setting up a PPPoE connection

1. WAN connection type: PPPoE
2. Get a WAN IP address automatically: Yes
3. Username: Your login according to the contract
4. Password: Your password according to the agreement
5. MTU: 1472
6. Save the settings with the button Apply.

Setting up an L2TP connection

1. WAN connection type - L2TP
2. YES
3. automatically- put a point on YES
4. Username and Password- login and password from the contract
5. VPN server -
6. The remaining parameters can be left unchanged. In the hostname, write something in English. Save settings.

Setting up PPTP (VPN) when automatically obtaining a local IP address

1. WAN connection type: PPTP
2. Enable WAN, Enable NAT, Enable UPnP - set it everywhere YES
3. Get an IP address and connect to DNS automatically- put a point on YES
4. Username: Your login according to the contract
5. Password: Your password according to the agreement
6. enter the IP address or name of the VPN server according to the contract
7. Save the settings with the button Apply.

Setting up PPTP (VPN) with a static local IP address

1. WAN connection type: PPTP
2. Get an IP address and connect to DNS automatically- put a point on No
3. IP address: We enter your IP address according to the contract
4. Subnet mask: We hammer in the mask according to the contract
5. Main gate: We drive in the gateway according to the contract
6. DNS server 1: And DNS server 2: enter your provider's servers (Rostelecom Omsk DNS 1: 195.162.32.5 DNS 2: 195.162.41.8)
7. Username: Your login according to the contract
8. Password: Your password according to the agreement
9. Heart-Beat or PPTP/L2TP(VPN) server: enter the IP address or name of the VPN server according to the contract
10. Save the settings with the button Apply.

NAT when automatically obtaining an IP address (DHCP)

1. WAN connection type: Dynamic IP
2. Save the settings with the button Apply

Checking Internet connection status

Saving/restoring router settings

After setting up, it is recommended to save them so that if problems arise, you can restore them. To do this you need to go to the tab Additional settings, menu Administration;, Restore/Save/Load settings tab.

• To save the current router settings, you must press the button Save. The settings file will be saved to the specified location on your hard drive.
• To restore settings settings from a file, you must click the button Choose File, specify the path to the settings file, then click the button Send.

Attention! Button press Restore will restore factory settings!