Usb device over current detected what to do. How to fix USB device over current status detected when turning on the computer. USB Device Over Current Status Detected: USB cables are shorting

(5 votes, average: 5,00 out of 5)

I turn on the computer and a recording comes out usb device over current status detected system will shutdown in 15 seconds, what does it mean? Translated, this roughly sounds like “A USB device with high current consumption has been detected, the system will reboot in 15 seconds.”

If the error usb device over current status detected appears, you should not immediately open the case of the system unit; first, let’s inspect USB port s of your computer.

How to remove the message usb device over current status detected system will shutdown in 15 seconds

1. Since the message says about a USB device error, let's start by disconnecting all USB devices on the computer, such as USB flash drives, USB cameras, mice, keyboards and other USB devices (you need to free all USB ports computer from connected external devices). We turn on the computer and see that the usb device over current status detected error has disappeared, if not, then go to the second point. If the message disappears, then the reason for the appearance of this message is a faulty connected USB device (the wire is broken, there is a short circuit - replace the faulty USB device with a new one).
2. If, after disconnecting all USB devices, the usb device over current status detected message is still an eyesore, then you need to inspect all USB ports for broken parts, foreign objects, and even dust inside the ports. There were cases when, after cleaning the USB ports from dust, the usb device over current status detected message disappeared.
3. In 90 percent of cases, as a rule, a broken connector is identified at the second stage. Which USB ports are used most often? Those located on the front panel of the system unit case. And even if you were unable to identify a faulty USB port, do not despair, disabling USB ports on the front panel will help in most cases.

Conclusion. The error is typical for ASUS motherboards, and it is not always worth seeking the help of a specialist to resolve errors when turning on the computer, and even with minimal knowledge of computer devices, some problems can be solved by an ordinary user on their own. And if the described actions did not help you eliminate the reason for the appearance of the message usb device over current status detected, then Possible Solution your problem is this:

• Check the USBPWR power management jumper; the absence of this jumper on the motherboard may also be the reason for the appearance of the message when starting the computer
• Malfunction of the resistor identifying the presence of voltage on one of the ports

If the computer writes a message when you turn it on USB device over current status detected! System Shut Down after 15 sec and does not boot, then most often the reason for this lies not in a malfunction of the motherboard or other components, but in problems with peripheral devices. If you translate the error into Russian, it means that the system has detected a device connected via USB that consumes a lot of current, and therefore the computer will restart in 15 seconds.
Sometimes it could be a simple BIOS glitch and restarting the device can really help. But if this does not happen, then there are two options that can be performed by any user without advanced computer knowledge.

How to remove the message USB device over current status detected - System Will Shut Down after 15 sec.

Step 1. We disconnect all devices connected via USB - flash drives, printer, camera, mobile phone and so on. Even the mouse should be turned off. We leave only the keyboard.

Turn on the PC and watch. Has the error disappeared? Then connect each device in turn and repeat the operation. This way you can determine which of them is responsible for the message “USB device over current status detected!” Computer shut down in 15 seconds." Having found it, carefully inspect the cable - it may be damaged and short-circuited. Otherwise, you will have to drag it in for repairs.

Step 2. Trying to reset the BIOS settings. There may be a more global failure of the PC's basic input/output system and it will need to be reset to factory settings. Here . The easiest way to do this is to remove the side cover of the case. There is a battery on the motherboard - remove it. Wait half an hour and put it back.

The error “usb device over current status detected” is gone?! If yes, great, but if not, I’m afraid that the situation is bad and most likely you will have to take the computer to a service center. However, before doing this, I advise you to do this - carefully inspect each of the computer’s USB ports to see if any debris has gotten into it, or if the contacts are bent.

Sometimes metal shavings or a piece of other conductive material that gets on the contacts can lead to a short circuit and, accordingly, problems with the operation of the PC. To clean them, use a small brush. For example, I use an old toothbrush to clean USB ports. Simple and convenient!

Fixing USB Device Over Current Status Detected error

Hello, visitor. If you've landed on this page, you've probably encountered a problem where your computer refuses to load Windows and displays the splash screen with the error:

Please enter Setup to recover BIOS Setting
USB Device Over Current Status Detected!!
Sustem Will shut down After 15 Seconds

It is a rare case when the system independently and correctly detected a malfunction. And displayed the type of breakdown directly on the screen. Inscription

USB Device Over Current Status Detected

means nothing more than a short circuit in the USB connector of the computer/laptop. What can be done about this?

The solution to a problem lies at its source.

Before you begin, clear the current BIOS settings by de-energizing the CMOS - remove the battery for a long time, simultaneously shorting 2 contacts on the connector next to the battery slot labeled CLEAR CMOS. Here they are on different boards:

USB Device Over Current Status Detected: the USB device itself is damaged

The first thing the user should start with is to remove ALL devices from the USB connectors, freeing them from any flash drive, modem, transmitter, etc. Restart your computer and check if the error goes away. If the system boots normally, the cause is shorted contacts wired mouse in the wire itself or in a connector clogged with dust. This can be easily checked by reconnecting the supposedly shorted device TO ANOTHER computer on occasion. Blow out the connectors, which, however, does not always work: dust can clog not only the contacts in the connector themselves, but also the space around the slot on the motherboard where the connector connects to the motherboard. There is only one way out: open the computer/laptop and use a brush to go over all the places where the USB connectors are attached.

USB Device Over Current Status Detected: connector damage

Yes, USB connectors on a computer are one of the weakest points: we constantly plug flash drives, external drives, modems... This is not always done carefully and there is no exact time when one of the contacts in the connector “falls”. The result will be the unexpected appearance of the indicated inscription and the shutdown of the computer, which thus protects the motherboard from damage. Exit: with the roof open and a clear view of the board, carefully inspect each of the connectors for visible damage and contacts that have fallen on each other. I’ll add to the article concrete example Later.

USB Device Over Current Status Detected: Check the jumpers on the board

According to some incomprehensible logic, component manufacturers, and more often assemblers in the workshop, incorrectly (or even never) read the manuals for the equipment being installed. The result is incorrectly set short circuits or jumpers for correct operation of the equipment. The system works more or less smoothly until the first failures, associated primarily with the physical aging of the equipment or improper operating conditions: dust, vibration, expiration of components. At some point, this is accompanied by signal attenuation, loss of communication between electronic components, and the appearance of incorrect self-diagnosis signals. In the end, we have what we have. Output: Check the jumpers on the connectors labeled USBPWR, USBPOWER, etc. Where there is no jumper, BE SURE TO INSTALL. Didn't work? Check that the board is firmly attached to the case and that there are no oxidized areas at the mounting points.

USB Device Over Current Status Detected: USB cables are shorting

There are some in your computer case, and they can also collect dirt and dust or fray at kinks. Reconnect the cables.

This is all you can do at home. Good luck.

Some users may encounter the “Unknown Device” problem, when the system either does not correctly detect any of its devices (visible by the corresponding icon and the Unknown Device inscription in the device manager), or when connecting any external device(usually a flash drive or external HDD) the latter is also not determined by the system. In this article I will tell you what Unknown Device is and how to fix it, I will describe the causes of such a problem and outline the tools for solving it.

What is Unknown Device

When determining what an Unknown Device is, you should first start with the translation of this phrase. Translated from English this means " Unknown device", and appears in a situation where Windows cannot identify a device and find a driver for it (which is what is displayed in Device Manager). Until for of this device the driver will not be found, this component either does not work at all or does not work properly.

Typically, Windows OS identifies most devices and independently selects drivers for them. When does this process fail or the system cannot produce automatic download the desired driver, then the user comes into play, who needs to personally identify the driver, find it on the network, and install it on his PC.

Moreover, this problem is often identified as error 43 (sometimes correlating with error 28) with corresponding options for solving it.

Causes of the Unknown Device problem

So, in defining what Unknown Device means, we will determine the main reasons that cause this system dysfunction. They are as follows:

• As I indicated above, this missing (incorrect) driver to any device;
• Operating system failure;
• Driver conflict after installing new devices;
• Damage to the OS registry;
• Action of virus programs;
• Failure of devices connected via USB connector(flash drive, HDD, USB cable, etc.);
• Breakdown of the USB connector on PC.

After we have figured out what this is an Unknown Device and what causes it, let's move on to how to fix Unknown Device on your computer.

Fixing Unknown Device is not working correctly code 43

Let's now try to figure out how to get rid of Unknown Device on our computer. To do this you need to do the following:

1. Restart your computer, often this method is a very effective solution to the problem;
2. Get rid of malware on your PC. For this, use anti-virus tools such as Web CureIt!, Malware Anti-Malware, Trojan Remover and a number of others. Check out the best protection and ;
3. Search and install the required driver for your device. Click on the “Start” button, type devmgmt.msc in the search bar and press enter. In the device manager that opens, right-click on the device labeled Unknown Device and select “Properties” from the menu that appears.

Go to the “Details” tab and in the “Property” option select “Equipment ID”. You will see several values ​​consisting of letters and numbers, this is the identification data of your problematic equipment. Copy this data and enter it into search engine and look for drivers for your problematic component (it is advisable to download drivers from the developer’s website). After finding the necessary drivers, download them and install them on your PC. After installing the drivers, the Unknown Device problem is often resolved.

If they don’t have drivers automatic program installations (and you have downloaded them to your computer), use the “ Update drivers» in the properties of the problematic device (as indicated above) and, if necessary, tell the system the path to the downloaded drivers on the hard drive;

Conclusion

Above I gave a detailed answer to the question - what is Unknown Device and how to fix it. In most cases, the occurrence of this dysfunction is associated with the problem of installing drivers for the required equipment, and to solve it it is enough to find and install necessary drivers(or use tools like Driver Pack Solution). If nothing helps, then perhaps the essence of the problem is a hardware failure of some system component, and you should contact your nearest service center to solve this problem.

Some users, when turning on the computer, may see a message on their monitors - USB Device Over Current Status Detected. Translated from English, this means that a USB device with high electricity consumption has been detected. If this error appears, do not immediately open the inspection cover. Try to inspect the external part of the system unit without touching it.

Solutions for USB Device Over Current Status Detected error

Most often, after the 2nd step of applying the cause elimination, the computer begins to work stably. First of all, you need to try the USB ports that are most often used. Typically, these are ports located on the front panel of the computer, take a closer look at them, you may be able to notice shades of carbon deposits, in this case the port is most likely burned out from overvoltage or improper operation. Even if you are unable to visually determine the failure, then sequentially disconnecting the devices should definitely resolve the issue with the error - USB Device Over Current Status Detected.

Other reasons for errors with USB

According to statistics, this error most often occurs on Asus motherboard models. For some errors, including this one, there is no need to immediately contact specialists from the service, because at least half of them any average user can solve on their own at home. If the above tips did not work for you and the error has not gone away, then you may need to try a few more tips:

• You need to reset the BIOS settings. This can be done in several ways: programmatically, using the CLRTC jumper, and also by removing the battery motherboard. You can read more about these methods on the Internet, each for its own model.
• Make sure that the motherboard has a USBPWR power management jumper; if it is not present, this may cause a USB Device Over Current Status Detected error when turning on the computer.
• The resistor that checks for voltage on the required port may be faulty, which is the cause of the error described above.

Checking the motherboard

The problem may also lie in the motherboard. Sometimes board manufacturers make various errors during production, as a result of which they can lead to serious consequences, unstable operation of ports and even short circuits.

The USB Device Over Current Status Detected error occurs when the shorts and jumpers are placed incorrectly. This leads to the fact that the system works stably for some time, until the first failure and then all sorts of errors begin related to the operation of plug-ins. In addition to the factory flaw, the motherboard becomes covered in dust after some time. This is all accompanied by a muted signal, failures in the communication of the motherboard components, and also by the fact that the system tries to diagnose itself upon startup.

• Next, with the computer completely turned off and de-energized, open the inspection cover and carefully examine the system board.
• Inspect the jumpers in the USBPOWER and USBPWR connectors. If they are missing, you must install them.
• It is also necessary to check where the board is attached to system unit, check these areas for oxidation areas.
• Check all ports and major components on the motherboard, you may be able to see scorched areas, these may be the result of a short on the port.

The cables also need to be checked at bending areas. Perhaps in one of these areas one or more wires are broken. In this case, the motherboard comes with additional cables; if there are none, you will have to buy new ones and replace them. If the cables are fine, try disconnecting them. Sometimes the contacts become clogged with dust and stop transmitting the signal. They need to be removed from the nest, blown out and put back in place. After that, put everything in place and tighten it.