Do-it-yourself acupuncture diagnostics and therapy device. A device for searching biologically active points on the human body. For the "Protective device" circuit

For drug-free correction of the body's condition, methods of stimulating biologically active points (BAP) are widely used. or points Difficulties in using these methods arise due to the difficulty of finding BAP on the human body, since the area of ​​BAP does not exceed 1 mm2. By controlling the resistance of skin areas in the places where BAP are supposed to be located with the proposed device, you can find them easily and unambiguously. The device is housed in a metal case measuring 96x38x39 mm. The building contains electrical diagram, power ingredient and switch. An insulator of the active search electrode is fixed on one end side of the housing, and indication LEDs are mounted on the other side. The passive electrode is a metal case, which is held in the hand when searching for BAP. Figure 1 shows a diagram of the device. An active search electrode is connected to the inverting input of comparator DA1. Resistor R1 determines the input resistance of the device, capacitor C1 serves to filter interference, resistor R2 restrains the current of the indicator LEDs HL1...HL3. Amateur radio converter circuits Variable resistor R4 regulates the voltage supplied to the human body (through the fingers holding the device body). Resistors R3 and R5 limit the limits of voltage change. The voltage between the search and passive electrodes is no more than 5 V, the current is no more than 0.5 μA. Current consumption in standby mode is 1 mA. and if the LEDs are lit - 5...bmA. The device is made on a printed circuit board, the drawing of which is shown in Fig. 2. It contains all the parts except the LEDs and the battery. The board is designed to use a variable resistor SPZ-9a; it is installed on the board on an L-shaped bracket. You can glue a scale (for example, 10 divisions) near the resistor handle....

For the "Electronic hydraulic level" circuit

When carrying out construction work, it is often necessary to accurately determine the parallelism of a horizontal surface relative to the ground. Some power tools (drills, hammer drills, etc.) have a small “level” built into the body (a glass flask filled with liquid with a bubble inside). The position of this bubble is used to determine the angle of inclination of the device relative to the horizontal surface. Such devices are called “gyros”. They are quite common in many areas of production, construction, etc. There are also gyroscopes - converters of tilt and angular velocity into an electrical signal. gyroscopes of the brands "ENC-03J" and "ENC-03M" have appeared on sale quite recently. They serve as state change sensors in video cameras and “cool” cameras to compensate for hand shake when shooting, as well as to detect their own movement. Radomcrophone circuits The electronic gyroscope has a high response speed (minimum inertia), low supply voltage (2.7..5.5 V depending on the model) and low current consumption (usually 5.15 mA). Characteristic linearity - ±5%, operating temperature range -5...+75°C. Unlike its mechanical counterpart, it is compact and lightweight (dimensions - 15x8x4 mm), weight (depending on the model) - 1.. 20 g. It does not contain fragile materials, and has a shock- and vibration-resistant body. Moreover, gyroscopes are produced in a CHIP version. which allows their use in miniature devices. Based on such an electronic sensor device, it is possible to create a simple “horizontal” control device. The sensor is a piezoceramic gyroscope “ENC-03J” (Fig. 1) manufactured by the company “Murala”. I purchased it from a radio component store...

For the diagram "DEVICE FOR TREATMENT WITH MAGNETIC FIELD"

Consumer electronics DEVICE FOR MAGNETIC FIELD TREATMENT. STAKHOV, 230023, Grodno, Lenin St., 8 - 13, tel. 47-01-66. Experiments with magnetic field treatment are now becoming relevant. Previously, wearing magnetic bracelets was recommended for this purpose. Although the results of their use are still controversial, many people constantly use them. Recently, small-sized electronic devices that can be worn in the same way as magnetic bracelets, but affecting the body with an alternating field of certain frequencies. These easy-to-use devices are used as an analgesic for headaches and migraines, as a stimulant for neurosis and fatigue, as well as for relieving rheumatic pain and etc. The frequency of the magnetic field is selected individually using the appropriate switches. Typically, lower frequencies are used to relieve rheumatic pain, and higher frequencies are used to relieve headaches. The minimum time for a daily session is 15 minutes. Miniature design devices makes it possible to attach it with a belt to an arm, leg or other parts of the body. The proposed option for magnetic field treatment (Fig. 1) contains one microcircuit - the KR1006VI1 timer. The timer is used to generate pulse signals of the required frequencies. Supply voltage Up=5...16 V, instability of the repetition period of the generated pulse signals from the supply voltage is 0.01% [I]. The timer is made using bipolar technology, and its powerful output stage provides a current Iout = 200 mA. Fig. 1 The operation of the circuit (Fig. 1) can be explained as follows. IN original condition capacitor C2 is discharged. It is charged through resistors R1, R2, R3. Voltage across condensate...

For the "CODE LOCK" scheme

Consumer electronics CODE LOCK. CHURUKSAEV, Kachkanar, Sverdlovsk region. The proposed version of the electronic combination lock differs from similar three-button locks in its simplicity and increased secrecy. Recording a code after typing it is carried out not just once, but by pressing the corresponding button multiple times, and this is different for different codes. The combination lock diagram is shown in Fig. 1. It includes buttons: SB1 - code entry, SB2 - code entry, SB3 - reset, and on elements R1, R2, C1, DD1.1, DD1.2 and R3. R4, C2. DD1.3. DD1.4 assembled circuits to suppress contact bounce. The DD3 counter has an encoding device - the code is set by appropriate switching of the DD3 counter outputs; outputs not involved in the code through diodes VD2...VD5 with the help of elements DD2.3, DD2.4, VD6 form a “reset” signal, which is supplied to the R inputs of counters DD4, DD5 in the event of an incorrect code entry. Elements DD2.1, DD2.2 are intended for writing code to counters OD4, DD5. Diodes VD7, VD8 generate a “Reset” signal at the R inputs of counters DD4, DD5 in case of incorrect code entry. K174KN2 microcircuit Elements DD6.1. R8, R9, C4, DD6.2, VD9 form a “reset” signal delayed by 4 s. A delay is necessary for the actuator to operate. Elements DD6.3, DD6.4 open transistor VT1 when the code is correctly dialed and entered. Relay contacts K1 switch the actuator. The power supply, consisting of VD12, R11, VD11, C5 (without a mains transformer with a quenching resistor), is built according to a traditional scheme. Puc.1 The combination lock works as follows. First, you need to briefly press the SB3 button, while a high level appears at the R inputs of counters DD3, DD4, DD5 - and the counters are reset. Then, by pressing the SB2 button, the code is entered according to the switching of the outputs of the counter DD3. In this case, the SB2 button must be pressed twice so that a high level appears at pin 4 of the DD3 counter, and low levels should appear at the other outputs. Now with the SB1 button you need to do...

For the circuit "THYRISTOR TEMPERATURE REGULATOR"

Household Electronics THYRISTOR THERMOREGULATOR The thermostat, the diagram of which is shown in the figure, is designed to maintain a constant temperature of indoor air, water in an aquarium, etc. A heater with a power of up to 500 W can be connected to it. The thermostat consists of a threshold devices(on transistor T1 and T1). electronic relay (on transistor TZ and thyristor D10) and power supply. The temperature sensor is the thermistor R5, which is included in the problem of supplying voltage to the base of the transistor T1 of the threshold device. If the environment has the required temperature, the threshold transistor T1 is closed and T1 is open. Transistor TZ and thyristor D10 of the electronic relay are closed in this case and the mains voltage is not supplied to the heater. As the temperature of the environment decreases, the resistance of the thermistor increases, as a result of which the voltage at the base of transistor T1 increases. Triac thermostat circuit When it reaches the device’s operating threshold, transistor T1 will open and T2 will close. This will cause transistor T3 to turn on. The voltage that appears across resistor R9 is applied between the cathode and the control electrode of thyristor D10 and will be enough to open it. The mains voltage will be supplied to the heater through the thyristor and diodes D6-D9. When the ambient temperature reaches the required value, the thermostat will turn off the voltage from the heater. Variable resistor R11 is used to set the limits of the maintained temperature. The thermostat uses an MMT-4 thermistor. Transformer Tr1 is made on a Ш12Х25 core. Winding I contains 8000 turns of wire PEV-1 0.1, and winding II contains 170 turns of wire PEV-1 0.4. A. STOYANOV Zagorsk...

For the circuit "Desulfating charger circuit"

Automotive electronicsDesulfating circuit charger circuit desulfating charger devices proposed by Samundzhi and L. Simeonov. Charger performed using a half-wave rectifier circuit based on diode VI with parametric voltage stabilization (V2) and a current amplifier (V3, V4). The H1 signal light lights up when the transformer is connected to the network. The average charging current of approximately 1.8 A is regulated by selecting resistor R3. The discharge current is set by resistor R1. The voltage on the secondary winding of the transformer is 21 V (amplitude value 28 V). The voltage on the battery at the rated charging current is 14 V. Therefore, the charging current of the battery occurs only when the amplitude of the output voltage of the current amplifier exceeds the battery voltage. During one period of alternating voltage, one pulse of charging current is formed during time Ti. Power regulator on ts122 25 The battery discharges during the time Tz = 2Ti. Therefore, the ammeter shows the average importance of the charging current, equal to approximately one third of the amplitude value of the total charging and discharging currents. You can use the TS-200 transformer from the TV in the charger. The secondary windings are removed from both coils of the transformer and a new winding consisting of 74 turns (37 turns on each coil) is wound with PEV-2 1.5 mm wire. Transistor V4 is mounted on a radiator with an effective surface area of ​​​​approximately 200 cm2. Details: Type VI diodes D242A. D243A, D245A. D305, V2 one or two zener diodes D814A connected in series, V5 type D226: transistors V3 type KT803A, V4 type KT803A or KT808A. When setting up the charger, you should select the voltage...

For the "Protective device" circuit

The proposed protective device automatically turns off the electric motor when switching from load mode to idle mode. This is especially useful for electric pumps if the well or borehole has a limited supply of water. The protective circuit is shown in the figure. The device works as follows. When the SB2 button is pressed, the thyristors VS1 and VS2 turn on the electric motor M1. In this case, the voltage on resistor R2 is rectified by the bridge VD5...VD8 and supplied to the thyristor optocoupler U1, which blocks the SB2 button. If the load on the electric motor decreases (the current consumption decreases accordingly), the voltage on resistor R2 also decreases and becomes insufficient to turn on the thyristor optocoupler U1, thyristors VS1 and VS2 turn off the electric motor. When setting up, you may need to select resistor R3. Thyristors VS1 and VS2 are installed on radiators. Resistor R2 is wirewound. V.F. Yakovlev, Shostka, Sumy region. ...

For the circuit "OVERVOLTAGE PROTECTION DEVICE"

Consumer electronics SURGE VOLTAGE PROTECTION DEVICE A.PAKALO, 340074, Ukraine, Donetsk-74, st. Volgo-Donkaya, 7 "g" - 5, tel. 22-26-93. I offer a simple device that, in the event of a power failure, will protect a TV, VCR, refrigerator, etc. from overvoltage. As a rule, in the event of an accident, a voltage of 380 V (rms value) is present in the network, which brings all sorts of troubles. In such a situation, the surge protector trips, creating a short circuit. “Knocked out” plugs (fusible or automatic) stop the supply of electricity to the apartment. The diagram is shown in the figure. The protection response voltage is approximately equal to 255 V. In reality, the response voltage is slightly higher due to the presence of resistor R1 in the threshold circuit. This resistor can be used to change the response voltage within certain limits. In the author’s version, Ucp = 270 V. Capacitors C1 and C2 form an RC circuit with R1, which prevents operation devices during pulse surges in the network, the circuit works as follows. T160 current regulator circuit When the network voltage is up to 270 V, the zener diodes VD3, VD4 are closed. Thyristors VS1, VS2 are also closed. When the current voltage value exceeds 270 V, the zener diodes VD3, VD4 open, and the opening voltage is supplied to the control electrodes of the thyristors VS1, VS2. Depending on the polarity of the mains voltage sub-period, the current passes either through the thyristor VS1 or through VS2. When the current exceeds 10 A, they trigger circuit breakers(plugs), protecting electrical appliances from burnout. There is no need to configure the device. Without capacitors C1 and C2, the response time does not exceed one half-cycle of the mains voltage, but false alarms are possible. Since capacitors C1 and C2 reduce the performance of the device...

For the circuit "Home network surge protector"

Due to instability electrical network(especially in rural areas) and overvoltage can cause household appliances to fail: light bulbs, various heating devices, electric motors of refrigerators and other appliances, radio equipment, etc. I offer an automatic device that monitors the state of the electrical network and automatically turns off and turns off the load. The load will be switched on only when the electrical network is in normal condition. The threshold circuit is powered from the network through quenching resistors R3, R4 and diodes VD1...VD4. Zener diode VD8 serves to stabilize the supply voltage of the circuit. The changing mains voltage is supplied through the diode bridge VD1...VD4 to the divider R1, R2. From the resistor R2 slider, which sets the device’s response voltage, the control voltage is supplied through the diode VD5 to the base of the transistor VT1. Block diagram of the 251 1HT microcircuit Zener diode VD6 is used to protect the transistor from high voltages. When the network voltage is higher than normal, the voltage at the base of the transistor increases, it opens and turns on relay K1. Contacts K1.1 close, relay K2 is activated and switches off the load with contacts K2.1. After the voltage in the electrical network is restored, relay K1 is de-energized and turns off relay K2, which turns on the load with contacts K2.1. LEDs VD10, VD12 are used to indicate the status of the device. Relay K2 - any with a winding operating voltage of 220 V, K1 - also any from the RES-9 series. Setting up devices comes down to setting the trigger voltage of the machine with resistor R2.N. Basenkov, Dobrush...

For the "INPUT FREQUENCY DIVIDER" circuit

Measuring equipmentINPUT FREQUENCY DIVIDER The preliminary frequency divider on the ESL KS193IE2 microcircuit allows you to significantly expand the scope of relatively low-frequency frequency meters assembled on conventional TTL microcircuits. The proposed divider, which is based on the operation of the above-mentioned microcircuit, divides the frequency of the input signal by 100. Schematic diagram devices shown in the figure. A two-way diode limiter is switched on at its input, protecting transistor VT1 from overload when applied to the input devices large signals. The cascade on the DD1 chip acts as a divider into 10. Transistor VT2 is used to assemble a device for matching the signal levels of the output of the ESL microcircuit with the input of the TTL microcircuit DD2, which also acts as a divider into 10. As a result, the total division factor of all devices is 100. The frequency obtained at the output can be measured with a frequency meter with a measurement limit of 5 MHz. A simple current regulator. Ordinary universal frequency meters are suitable for this. Integrated circuit KS193IE2 operates normally with a supply voltage of 5 V ±5 percent(s). The minimum input signal frequency is 10 MHz (although 5 MHz is acceptable), the maximum is up to 500 MHz. Achieving maximum capabilities devices frequency depends to a large extent on the choice of DD2 microcircuit. So, when using a serial counter of type 7490, stable operation devices remains up to 210 MHz; when using an LS series microcircuit (74LS90), the boundary line of the input signal frequency can be increased to 290 MHz. A device assembled from serviceable elements does not require adjustment. To obtain good results at such a high input signal frequency, volumetric resistors and ceramic capacitors Installation

The guiding thought of Chinese medicine is the concept of wholeness. The basis of physiology and pathology is the internal organs of Zangfu and Jingluo channels. A feature of the theoretical system of medicine is dialectical treatment.

Chinese medicine believes that when a disease invades the body, the regulation of the Yin Yang balance is first affected. The Yin Yang balance loses regulation and illness occurs. In the Shuboshi - Convenient Doctor - Comfort acupuncture medical devices, Chinese acupuncture and massage are transformed into healing waves through modern high technology. Based on the concept of a single whole organism, in combination with local treatment, these waves affect the corresponding points of the Jingluo channels and achieve the goal of restoring the balance of Yin Yang and curing the disease. The method is easy to learn and use. Every person, through simple study, can master Chinese acupuncture and massage, and by using Chinese acupuncture and massage at home, achieve the goals of prevention and treatment.

What is Yin Yang?

Yin Yang is a generalization of some interrelated and opposing things and phenomena of the natural world. At the same time, there is the concept of opposition and unity.

Everything that moves sharply, what is outside, what is above, what is hot, what is bright, all this is Yang.

Everything that is in relative peace, whatever is inside, whatever is below, whatever is cold, dark, everything is Yin.

However, the belonging of things to Yin Yang is not absolute, but relative. They may change as conditions change. The balance of Yin and Yang among themselves is also not at rest and not absolute. Within certain limits and at certain times, “Yin decreases, Yang increases” and “Yang decreases, Yin increases,” thus maintaining a relative balance.

The normal development of the life of an organism is achieved through continuous decrease and increase and continuous maintenance of balance. When the balance is undermined, illness may occur in the body: Yin strengthens and Yang weakens, Yang strengthens and Yin weakens. Strengthening Yang means heat, strengthening Yin means cold.

Chinese medicine believes that disease is inseparable from Yin Yang. We add where there is a shortage, throw away where there is excess. Restoring Yin Yang balance is the basic principle of treating disease.

Relationship between zangxiang and illness

Zang are the internal organs. Xiang is the external manifestations of physiology and pathology. People assert the presence of disease through observation and examination of physiological and pathological manifestations of functions internal organs.

Chinese medicine classifies the heart, lungs, spleen, liver, kidneys as the five zang category, and the gallbladder, stomach, small intestine, large intestine, bladder, three heaters as the six fu category. Brain; the spinal cord, bones, blood vessels, gall bladder, and uterus are called qihengzhifu.

Chinese medicine believes that the five zangs and six fus have Jingluo channels associated with them, in addition, they are interconnected. All diseases that arise in the five zang and six fu can be treated by influencing the points located on the jinglo channels.

The first of the five zangs is the heart.

The heart controls blood circulation, controls mood, and its external manifestation is the tongue. The condition of the heart shows on the face. It corresponds to the human mood of “joy” and manifests itself in a liquid - “sweat”. His Jingluo channel is “Shoushaoyin Xinjing”, which is connected with the “Shoutaiyangxiaochangjing” channel, the channels of the small intestine and through this interaction the Yin Yang is maintained.

The second of the five zangs is the lungs.

The lungs control the “qi” of the body, breathing, the movement of fluid in the body and all the Jinglo channels, our skin. Their external manifestation is the nose. The condition of the lungs manifests itself on the hairline of the body. The lungs correspond to the human mood of “sadness” and appear in the liquid - “snot”. Their Jingluo channel is “Shoutaiyinfeijing”, which is connected with the “Shouyangmindajunjing” channel, the large intestine channel, and through this interaction the Yin Yang is maintained. When disease sets in in the lungs, abnormalities can occur in all the physiological activities that they control. In this case, we can treat by influencing the points located on the “Shoutaiyinfeijing” and “Shouyangmindachingjing” channels.

The third of the five zangs is the spleen.

The spleen controls the body's absorption of nutrients, the movement of body fluids, blood, muscles and limbs. Its external manifestation is the mouth. The condition of the spleen appears on the lips, and it corresponds to the human mood of "meditation" and appears in the liquid - "saliva". Her Jingluo channel is "Zutaiyinpijing", which is connected with the "Zuyangmingweijing" channel, the stomach channel, and through this interaction the Yin Yang is maintained.

When disease occurs in the spleen, abnormalities can occur in all the physiological activities that it controls. In this case, we can treat by influencing the points located on the Zutaiyinpijing and Zuyangmingweijing channels.

The fourth of the five zangs is the liver.

The liver controls the movement of "qi" in the body, controls and stimulates nutrient absorption, blood conservation, joints and movement. Its external manifestation is the eyes. The condition of the liver is manifested on the nails, it corresponds to the human mood of “anger” and appears in the liquid - “tears”. Her Jingluo channel is "Zujueyinganjing", which is connected with the "Zushaoyangdanjing" channel, the gallbladder channel, and through this interaction the Yin Yang is maintained.

When the liver becomes diseased, abnormalities can occur in all the physiological activities it controls. We can treat by acting on the points located on the “Tzujueyinganjing” and “Tzushaoyangdanjing” channels.

The fifth of the five zangs is the kidneys.

The kidneys control growth, physical development and reproduction. They control and regulate the flow and exit of fluid in the body and the absorption of “qi”. It manifests itself through the ears and anus and urinary organs. The condition of the liver is manifested in the hair of the head, it corresponds to the human mood of “fear”, and appears in the fluid “sperm”. Her Jingluo channel is "Zushaoyinshenjing", which is connected to the "Zutaiyangpanguangjing" channel, the bladder channel, and through this interaction the Yin Yang is maintained.

When the liver becomes diseased, abnormalities can occur in all the physiological activities it controls. In this case, we can treat by acting on the points located on the “Tzushaoyinishnjing” and “Zutaiyangpanguangjing” channels.

Main points of Jingluo channels:

II. Rules for working with Shuboshi - Comfort devices

First of all, you should carefully read the operating instructions for the device in order to master the basic ways of using the device and know what to pay attention to. Only after reading and understanding will Shuboshi - Comfort acupuncture devices serve you best.

How do the Convenient Doctor series devices help me improve my health?

The device of the “Convenient Doctor” series is a modern representative of Chinese medicine. It has accumulated all the best from thousands of years of Chinese medicine. Science and technology have reached today's heights, and we can use these products.

In everyday prevention, Shuboshi-Comfort acupuncture devices can be of great help to children, youth, middle-aged and old people, and women. When encountering a disease, the Convenient Doctor stimulates the points of the Jingluo channels and removes ailments and symptoms very effectively. For diseases of the neck, shoulders, back, lower back, legs, joints caused by acute injuries, chronic fatigue, bone proliferation, etc., the effect of the “Convenient Doctor” is very high! But you must remember that in case of acute injuries, you can start using the device only 24 hours after the injury.

Devices of the “Convenient Doctor” line (JJQ-1 and FZ-1) have 4 modes each, how should they be selected?

First mode of the JJQ-1 device: TONIZATION MODE. Strengthening the performance of the body and systems, the activity of the immune system, stress resistance (corresponds to Mode I of the FZ-1 device, but has a more effective impact power of 0.55 W (versus 0.45 W in the FZ-1).

Second mode of the JJQ-1 device: STIMULATION MODE. Activation of the processes of restoration of organs and systems destroyed by the disease. Unlike FZ-1, it affects the deep branches of the channels, which provides a more complete effect on individual organs and systems in order to eliminate chronic diseases (conditionally corresponds to Mode III of the FZ-1 device, but more accurately imitates the function of TCM acupuncture than the FZ device -1).

Third mode of the JJQ-1 device: HARMONIZATION MODE. Balances the flow of all basic vital processes in the body. Restores the balance of Yin and Yang and increases the body's defenses, strengthens the immune system (very roughly corresponds to Mode IV in the FZ-1 device).

Fourth mode of the JJQ-1 device: RELAXATION MODE. Relaxation, stress relief, anticonvulsant, antispastic effect. Complex effect on biologically active zones of the foot (partially corresponds to Mode II in the FZ-1 device).

Mode IV of the FZ-1 device: Combines modes I, II and III of the FZ-1 device.

The choice of modes is made on the basis of the theory of integrity - one of the most important theories of Chinese medicine. It is made based on a specific person, according to different diseases, a specific situation, a specific approach.

How to regulate the force of influence when using “Convenient Doctor” devices?

Since people have different sensitivity, treatment is carried out in different places and in different modes, the strength of the effect is different. But there are 2 criteria for determining the correct force of influence:

1. At the site of application, the muscles contract, in addition, there is no unpleasant sensation;
2. There is a feeling of numbness at the application site, in addition, you are able to withstand it.

How is the device usage time determined?

Under normal conditions, the device can be used 1 - 3 times a day, the duration of the session is from 30 minutes to 2 hours, but no more than 6 hours in total during the day. The average course of treatment is 2 weeks, after which it is usually recommended to take a break for 1 - 7 days and, if necessary, repeat the course of treatment. Usually the therapeutic effect is observed after 1 month.

What should I do if I don’t feel any results after using Shuboshi devices?

• "Have you found the correct place of use?"
• "Perhaps the force was too low?"
• "Perhaps the treatment period was too short?"

If you solve the above three questions, you will definitely be satisfied with the healing effect!

I take medication while using the device. Should I stop?

Don't stop. For Chinese medicine, treating a disease is a long process of regulation. Treatment takes some time. In addition, Chinese medicine in China has never oppressed Western medicine. The best way treatments are a combination of Chinese and Western medicine.

Before using Shuboshi - Comfort devices, what preparations do I need to make?

• Check if the device is correct;
• Check if the contacts are in good condition;
• Clean the area of ​​use, remove grease, dirt and dust from the skin;
• Relax and start treatment with ease.

What to do if the device cannot work normally?

• Sensitivity. The force of impact is reduced, there is no way to increase it.
  The battery is low - replace the battery.
  The adhesiveness and conductivity of the electrodes has decreased - replace the electrodes.
• There is a normal image on the screen, the indicator is on, but there is no sensation.
  Is the plug inserted well into the inlet? Turn off the device and check the connection.
  Check if the wire is broken; if so, replace the wire.
  The electrodes are completely out of order - replace the electrodes.

  If, after correcting the above problems, the device works, continue using it. If the device still does not work, contact our center.

• If the screen backlight is weak or almost non-existent, please replace the battery;
• When using: weak impact force, the work stops and then resumes, a feeling of electric shock.
  Poor wire contact - replace wire.
  Insufficient stickiness of electrodes - replace electrodes.

  If the wires and electrodes are in order, but the device does not work, contact our center for further instructions.

More detailed answers to popular questions regarding Shuboshi-Comfort devices can be found on the Frequently Asked Questions page.

How to take care of the device on a daily basis?

• Electrodes are a wearing part. To extend their service life, you should clean the area of ​​use each time before use, and apply after use. protective film. If the adhesive surface dries out, lightly moisten it with clean salt water;
• Do not use the device in a damp environment as this may affect its normal work;
• Store in a cool dry place.

III. What to pay attention to before starting to work with the device

Chinese medicine treats diseases by regulating the balance of Yinyang in the body. For this process it takes quite a long time. Therefore, when using any of the Shuboshi or Comfort devices, you should continue to take the medications you were taking before using them.

As you recover, you can reduce the amount of medication you take, even stopping it. Persons who have a pacemaker, artificial organs, or metal parts installed are prohibited from using the “Convenient Doctor” devices.

During use, do not place the paws on the heart area.

Persons with heart disease and hypertensive patients are not recommended to use too much force or too long a session.

All pain in the neck, back, lower back, legs, joints should be treated according to the Operating Instructions, according to the principle - where it hurts, stick there, the force of influence is quite high.

When used by children, it is necessary to control the force of influence on the part of adults, which should not be too great. In relation to various diseases, taking into account the individual characteristics of the body, having received recommendations from a consultant - a specialist in Chinese medicine on the use of the device, they should be strictly followed.

IV. Prevention using Shuboshi - Comfort devices

Chinese medicine pays great attention to the treatment of illness that has not occurred, prefers prevention, and regulates the balance between Yin and Yang so that people do not get sick or get sick less often. The most important function of Shuboshi is prevention.

1. Prevention in children

1.1 The peculiarity of children is that their internal organs are delicate. Prevention should be aimed at strengthening their integral constitution, regulating the physiological functions of the internal organs in order to stimulate their healthy growth and physical development.
Selection of points: + (63+66).

1.2 In children, lung function is not fully developed. But the lungs are the body's most important organ of resistance to disease. If you regulate your lungs at this time, you can strengthen the respiratory system and prevent the onset of diseases.
Selection of points: + (48+48).

1.3 In children, the functions of the gastrointestinal fact are weakened, the function of the spleen is not fully developed, which can easily lead to digestive disorders and slow growth. If the spleen and stomach are adjusted at this time, the digestive system can be strengthened and growth and physical development can be stimulated.
Selection of points: + (52+52).

Attention: Each combination of points should be affected once every 2 days, for 10 minutes, in the 1st or 4th mode. The force of impact should be set depending on the child’s sensations and muscle movements.

2. Prevention in young people

Young people integrate into society and are easily susceptible to bad habits: smoking and excessive drinking are bad. The following points help in relation to quitting smoking and alcohol.
Selection of points: + (81+70) (from both sides).

Attention: Apply each combination of points 2 times a day for 20 minutes, in the 1st or 3rd mode. The impact force is the maximum you can withstand.

2.1 Young people gradually develop reproductive and urinary systems, but they can very easily develop problems. Loss of spirit, menstrual irregularities, cold hands and feet, anxiety and other symptoms may occur. If you make adjustments at this time, you can not only eliminate the above symptoms, but also improve the health of the body.
Selection of points:

A. Borodai
Radio 2, 1998

The diagram of one of the stimulators is shown in Fig. 1. Its main parts are a 564 or K176 series microcircuit, an HL1 LED indicator and a VT1 transistor, on which a matching (buffer) stage is made. In addition, the stimulator is equipped with probes X1 and X2, of which X1 is considered active - it is moved around the body and the desired point is found, and X2 is passive, attached, for example, to the hand.

Elements DD1.1, DD1.4 contain a biologically active point detector (BAP), and elements DD1.2, DD1.3 contain a stimulating pulse generator. When probe X1 hits an active point, the resistance of the human body in this place drops sharply, as a result of which almost a logical level of 0 appears at the input of element DD1.1, and therefore at the output of DD1.4. The lit LED HL1 informs about the found point.

At the same time, the logical level 1 that appears at the output of element DD1.1 allows the generator to operate. The pulses it generates pass through a matching cascade and arrive at the active probe X1, and through it to the patient’s body. Diode VD1 prevents the passage of pulses to the input of element DD1.1 and at the same time, during pauses between pulses, allows you to maintain the BAP search mode. Thus, there is no need for a button, typical for such stimulators, which switches the probes from the point search mode to the stimulation mode.

Variable resistor R1 sets the threshold for automatic operation individually for each patient, resistors R4 and R5 set the repetition rate and duration of stimulating pulses, and resistor R9 sets their amplitude. The device parts can be placed in a small metal case, which also serves as a passive probe. To make an active probe, a used ballpoint pen is suitable, a wire is soldered to the writing unit of which, and a medicinal product is poured into the body if necessary - then the stimulation procedure will be combined with electrophoresis (a therapeutic method of influencing the body with direct current and medicinal substances administered with its help through the skin or mucous membranes).

If, in addition to light, a sound indication of the search for BAP is also needed, the stimulator should be modified, as shown in Fig. 2. The cascade on transistor VT2 together with the cascade on element DD1.4 form an AF generator, the signal of which is converted into sound by the piezoelectric emitter BF1.

It should be noted that in the stimulator pulse generator, when adjusting the frequency, the duration of the pulses changes slightly, and when adjusting the duration, the frequency changes slightly.

In Fig. Figure 3 shows another diagram of a stimulator in which the pulse generator is designed differently, which made it possible to avoid the mutual influence of the frequency and duration of the pulses. In addition, the generator using elements DD1.1 - DD1.3 is powered from element DD2.1.

Generator of light and sound signals, made on elements DD2.3, DD2.4, is modulated by the signal of the stimulating pulse generator - this allows you to visually and auditorily control the frequency of stimulating pulses. With the element values ​​indicated on the stimulator diagrams, the pulse frequency can be changed variable resistor from 10 to 150 Hz, and duration - from 0.5 to 5 ms.

Attention! You can use devices of this type only after consulting a doctor!

This simple electrical stimulator allows you to search for biologically active points on the human body (shiatsu or zhenjiu therapy) and automatically stimulate them with a weak current of a special form, which will have the same effect as the well-known acupuncture procedure. This method can be successfully used for the prevention and treatment of many diseases at home after consultation with a doctor and all his recommendations!

The work of the stimulator is based on the effect that in the place where the active point is located close to the surface of the skin, the resistance of the human body decreases sharply. This can be easily checked even with a regular tester turned on to measure maximum resistance (usually 2 MOhm), if you hold one of its probes in your hand and touch different parts of the body with the other. The resistance of different sections will vary quite noticeably. Thus, the operation of the device is based on the effect of changing the resistance of different parts of the body.

In many different sources, including on the Internet, you can find maps of the location of biologically active points on the human body, however, the exact position of each point may differ slightly for different people, and it can be determined accurately using the simple device proposed here.

Several drawings of maps of acupuncture points on the body

Schematic diagram of the stimulator

The circuit is a simple pulse generator, the frequency of which is determined by an RC circuit. Here R is the resistance at this specific point of the human body. Since the resistance at different points is different, the generation frequency will also be noticeably different. The lower the resistance of the skin area, the higher the frequency. Therefore, the procedure for finding a biologically active point (BAP) consists of searching for a pinpoint area of ​​the skin where the frequency of LED flashing and the sound of the piezo emitter will be the highest. In this case, one of the electrodes is a metal plate on the body of the device (or the body of the device itself, if it is metal), providing reliable contact with the hand, and the second is a metal pin, by moving which across the skin BAPs are searched for. Power can be from any batteries or accumulators with a voltage from 4.5 to 12 V.

Operation of the biostimulator circuit

A simple pulse generator is assembled on a microcircuit. This may be a digital MS type K561LA7 (shown in the diagram). It contains 4 NAND elements in one package. You can use others, for example, K561LA9, where there are 2 AND-NOT elements, but with three inputs:

The power of generated pulses with such a microcircuit will increase. Or others, similar to MS series 561, 174, 164, 155. But in this case, one should take into account the possibility of a different pinout and supply voltage range of the microcircuit. MS with OR-NOT elements are also suitable:

The diode bridge generates pulses of a certain polarity. Its diodes can be any low-power ones, for example KD520, 521, 522, etc. The LED indicator is also any, the brightness of its glow can be adjusted by trimming resistor VR1 (its resistance cannot be reduced to zero, otherwise the LED may burn out!) Therefore, it is better to choose a constant resistor of the required value. The piezo emitter can be installed or not. It does not affect the normal operation of the device in any way and is only needed for sound indication of the device’s operation, if necessary. It can be of types ZP-1, ZP-2, ZP-4, ZP-5...

The board drawing is here. The homemade stimulator does not require any adjustment. Connect the power and, if all elements are working, it immediately starts working. In the initial state, when the resistance between the electrodes is high, the generator does not generate anything. The LED may light constantly or not light at all. When the probes touch, generation begins. The LED begins to blink more often, the lower the resistance between the probes and, therefore, the closer the biologically active point. When it hits the BAP point directly, the LED blinks at maximum frequency. When using a sound emitter in a circuit, the sound also reaches its maximum frequency. When you hold the probe on the BAP, it is stimulated with a pulsed current.

In the specialized literature and other sources there are recommendations on which impulses of what polarity are best to influence BAP. As a rule, it is recommended to act with negative impulses. In this case, the second, positive electrode should be held in your hand, or applied to another place (you should get recommendations from your doctor about this). You can add a switch to the device for convenience and use it to change the polarity of the impact pulses. How to do this is shown in the figure below:

The electrical stimulator can be assembled in any suitable plastic or metal housing. If the body is metal, then one of the electrodes should be connected to the body. If the body is made of dielectric, then a metal plate or foil should be glued to it, connected to one of the electrodes.

Video about electronic acupuncture stimulator

Below are photos of a possible design of the device, assembled in a small-sized electrical switching box.

V. Kozlov

Electroacopuncture is a modern version of classical acupuncture, in which the so-called active points on the skin of the human body are excited by electrical impulses. In electroacopuncture, needles are not used and therefore this method It is most suitable for those patients who are afraid of infection during acupuncture, as well as for those who want to practice electroacopuncture on their own.

To search for active points, together with the stimulator I used an electronic LED ohmmeter. The ohmmeter measurement limit is G MΩ. As numerous measurements have shown, the skin resistance at active points is approximately 1 MOhm. The electrical circuit diagram of the stimulator is shown in Fig. 1. The stimulator is made on four inverters and a transistor switch VT1. The first two inverters form single-ended multivibrator, at the output of which another pair of inverters is connected, connected in parallel as an invertible buffer. With the help of capacitor C2 and diode VD3, pulses are formed with an amplitude almost equal to twice the supply voltage. In practice, the stimulator can be used when the supply voltage is reduced to 5 V, but at the same time reduced accordingly. The amplitude of the output pulses also varies. The ohmmeter is made on two transistors VT2 and VT3, forming an amplifier direct current(UPT) with high input impedance. Resistors R6 and R7 limit the base current of the transistors, eliminating their saturation mode. Capacitor C4 creates a negative circuit feedback by alternating current. Resistor R8 determines the upper limit of measurement. The device is powered by a Krona battery. Scheme printed circuit board shown in Fig. 2

The device is mounted in a small plastic case, which contains a stimulator circuit with an ohmmeter and a probe connected to the case with a four-wire cord from the handset. The probe contains two electrodes: active and passive, as well as a push-button switch for the type of work. The active electrode is made in the form of a pointed rod with a radius of curvature at the end of 0.3-0.4 mm. The passive electrode must be in the form of a rod or plate. Both probes are made of stainless metal and then polished. To use the stimulator, you need to pinch the passive electrode with the fingers of your left hand. With the tip of the active electrode we touch the place where the active point is supposed to be located, which should be slightly moistened beforehand. When this point is found correctly, the LED on the device lights up. Then, by pressing the button located on the probe, we switch the device to stimulation mode. To do this, use a potentiometer to increase the amplitude of the pulses according to your sensations. Typically, the most preferred mode is one in which a slight tingling sensation is felt. This point is stimulated for 15 - 20 seconds. It is undesirable to stimulate many points in one session, as well as points located on the head. The probe uses a KM2-1 switch, consisting of two microswitches. The passive electrode is connected to the probe using a miniature connector used in transistor receivers to connect telephones.

Literature:

1.E.Savitsky. "Instead of an arrow there is an LED." "Modelist-Constructor", 1982, 10
2. M. Tsakov. "Electropuncture stimulator", "Radio, television, electronics", 1990, 3