How to properly dry your phone in rice. How to dry a phone that has fallen into water. The worst situation

Sometimes a few drops of water or high humidity are enough for the phone to break or stop working properly forever. Undoubtedly, the best solution would be to seek help from service workers. But what to do if this is not possible?

Here are 10 first aid tricks for your cell phone if it gets wet.

1 . The phone must be removed from the water as soon as possible and turned off immediately. The fact is that phone parts let water through in a matter of seconds. Do not turn on your phone until you are sure it is dry. In addition, water that gets into the phone can cause a short circuit.

2 . Immediately after removing the phone from the water, remove the cover and remove the battery. This will help reduce the risk of damaging internal circuits. Gently dry the phone and its parts with paper towels or a soft cloth.

3 . Remove the SIM card. It should be wiped dry, set aside and allowed time to dry until the phone itself is ready for use.

4 . You need to unplug and remove everything peripherals, such as headphones, memory cards, as well as anything that can clog gaps, crevices and cracks in the phone (cases and protective films).

5 . If you have a vacuum cleaner on hand, use it to blow out the water. To remove residual moisture, you need to blow off each part of the phone for 20 minutes. In this case, the phone must be blown from all sides, constantly turning it.

Don't put your phone too close to the vacuum cleaner hose, otherwise static electricity will form, which will be even worse for your phone.

6 . Do not use a hair dryer to dry your phone, even on the “gentle” setting. By doing this, you can blow moisture from the surface further into the phone, which is especially dangerous for electronic components hidden deep inside the phone. You can also melt some parts of the phone.

7 . You can try to dry your phone by immersing it in a bag of dry rice. Rice draws out and absorbs moisture well, so there is a chance that all the moisture from the phone and battery will be absorbed into the rice and this will slow down corrosion. When placing your phone in rice, you should remove the cover, take out the battery and put them in the same container.

You need to keep your phone in a bag or container with rice for at least 2-3 days. This process is slow and rushing will only do harm. While the phone is drying, you need to turn it over from time to time so that the water is better absorbed.

Instead of rice, you can use silica gel, which is often put into shoes and other items when sold; it absorbs moisture better than rice.

It is worth checking the phone, placed in a container with absorbent material, every hour for the first 6 hours. If moisture has collected on the surface, you need to dry it again with paper towels or blow it with a vacuum cleaner.

8 . Place the phone in a sunny place to allow all holes to dry completely.

You can place the appliance on absorbent wipes or paper towels, even if it has previously been dried with a vacuum cleaner or placed in a container with rice. This will help absorb any remaining moisture from the device.

9 . After at least 24 hours, check that the outside of the mobile phone appears dry. It's worth checking all the ports, compartments and slots. If your phone looks dry and clean, you can replace the battery and try turning it on. Pay attention to possible strange sounds and noises that accompany the switching process: if there are any, then this is a sign that the phone is not functioning properly.

10 . If your phone appears dry but won't turn on, a dead battery may be to blame. Put your phone on charge. Then try turning it on again.

If connecting to the charger also does not help, then you should still try to contact a service center. But there is no need to hide the fact that it was damaged by water - the phone still has indicators that show the cause of the malfunction. The more detailed the circumstances are, the easier it will be for specialists to identify the breakdown and fix it.

Never vacuum a wet object. You may get an electric shock.

It is important to dry your phone before charging it.

Do not expose your phone to prolonged heat if you do not want parts of it to melt. Do not heat the battery; it may leak or explode.

Do not try to completely disassemble the phone yourself. Leave this to the professionals, as such experiments can lead to short circuits or poisoning with harmful chemicals.

Inattention, absent-mindedness, forgetfulness, or simply a random coincidence of circumstances very often confront us with the task of how to dry a phone that has fallen into water. And this can happen not only while relaxing on a pond, but also in your own apartment. Modern phones accompany us everywhere. On the one hand it is convenient. On the other hand, they threaten the device, without which the majority can no longer live, with unexpected problems. And one of the most common problems is getting the phone wet.

The worst situation

Electric shock

Imagine that your phone is charging, that is, connected to electrical network, and it is at this moment that a mug of tea, coffee or any other drink is accidentally poured onto him. The first, almost instinctive movement will be to grab the phone and wipe all the moisture off it. This should not be done under any circumstances. You could simply get electrocuted.

If immediately after the incident the traffic jams did not go out and the lights did not go out in the apartment, this does not mean that the danger, especially for you, has passed. The first thing you should do is turn off Charger from the network, or turn off the electricity altogether, and only then take any action to save the phone itself.

The phone fell into the water: algorithm of actions

There is a strong opinion, which is actively supported by manufacturers, that if your device falls into water or a sufficient amount of liquid is poured onto it, this at least means that you will have to go to a store that sells spare parts for cell phones, or even buy a new one, but this is not entirely true. If you act quickly, confidently and logically, you can often save your phone.

• The main rule is as follows: than faster phone removed from the water, the greater the chance that it will continue to function. There is no time for disgust or fear of getting your expensive manicure wet. No matter what tank you have to take out your phone or hands from, you can always wash them with soap later, which is much cheaper.
• If this trouble occurred while the phone was turned on, you need to turn it off in any way. The button does not work, which means you need to remove the battery. You can’t delay with this either, and it’s certainly not recommended to test it for performance. By trying to press any button other than turning it off, you risk completely killing the phone.
• Then, you should arm yourself with the necessary tools, sit in a comfortable, well-lit place and disassemble the phone. Not easy to take off back cover, remove the battery and SIM card. You need to try to remove everything that is possible and at the same time not forget in what order it was all done, so that you can put it back together later. If your touchscreen phone has fallen into water and the question arises of how to dry it, you shouldn’t get lost. It can also be disassembled, but this will require a very small screwdriver and maximum attention and accuracy.
• After you have been able to unscrew and remove everything that is possible and have laid it out on a clean and dry towel, each part should be blotted with paper napkins and with them, twisted into flagella, try to get into the most inaccessible places. There is one caveat here. You should not wrap a napkin around a match or toothpick. In this case, the flagellum will become too hard, and the possibility of causing mechanical damage to fragile parts will increase several times.
• You cannot immediately collect the field for this operation, much less turn on the phone. No matter how much it may seem to you that there is not a single molecule of liquid left inside the device and on the removed parts, this is not so. The phone should be left disassembled for several days and only then try it in use.

Degree of wetness

Superficial wetting

Agree that this indicator is quite important and, it turns out, many phones and smartphones provide the ability to determine this purely visually. If you remove the battery, you will see a small white circle or square near the charging hole.

This is an indicator showing the very degree of wetness. If it turns from white to pink or even red, then the phone that fell into the water should be dried.

Hair dryer or vacuum cleaner

Another deeply erroneous opinion is that in order to speed up the drying process, you can use a hair dryer to dry your hair. A strong air flow, on the contrary, will drive moisture into places where it will simply be impossible to dry it. And if you also turn on the hair dryer to heat, this may lead to overheating of some parts.

A vacuum cleaner is much safer in this case. On the contrary, it works on suction and therefore draws out moisture. This is not to say that this is an ideal and highly effective method, but it certainly won’t do any harm. So before you do anything, you should think carefully about how to dry a mobile phone that has fallen into water, and do it correctly, without causing even more damage.

Proper drying

Drying your phone in rice

Let us remind you once again: in order to dry your phone so that it continues to work, you should never rush. Neither paper napkins nor a vacuum cleaner will ensure a complete absence of moisture - they will only significantly reduce its amount. But even a small drop can be enough for the phone to burn out if turned on at the wrong time. Several days in the air are simply necessary, but this process can be accelerated by placing the device in an adsorbing medium.

The easiest way to create it at home is in three ways:

• Regular rice. Any grain absorbs moisture very well, but rice is the cleanest. The disassembled phone should be individually simply buried in rice and literally overnight it will draw all the moisture out of it. The remaining dust can be easily removed with a dry cloth.
• Silica gel. If you recently bought a new pair of shoes and have not yet thrown out the box, then you can use special small balls that shoemakers pour into their products to remove excess moisture. They are also suitable for drying a phone that has fallen into water.
• Cat litter. Its purpose is exactly what is needed. It is better to use a fine litter and carefully ensure that your pet does not confuse the place where it needs to go to the toilet.

Other types of liquid

How to dry your phone if beer spills on it

We told you how to properly dry a phone or smartphone that has fallen into water, but it often happens that they fall into other liquids, which, in addition to moisture, also contain sugar, all kinds of sticky substances, and even brewer’s yeast. In this case, in addition to getting wet, contamination will certainly follow. The first instinct of many people is to rinse the device under a stream of clean water. Do not do that.

Follow the algorithm of actions given above, the main purpose of which is to dry the phone. After this, the dirt will need to be thoroughly wiped off with wet wipes and dried again. Of course, this takes a little longer, but it eliminates additional damage.
A phone gurgling into water is a very big nuisance. You can suddenly lose a very necessary and useful thing, not to mention its cost. However, there is no need to despair. If everything is done quickly, but slowly, and correctly, it is quite possible to save him.

By carelessness, a phone that has fallen out of your hands and ended up in water can be saved from imminent death at home. The main thing is to act quickly, then you will be able to save on buying a new gadget. You can dry your phone from water using improvised objects and unusual means: napkins, a vacuum cleaner, rice, cat litter and silica gel. You can also take the device to a service center to solve the problem.

After the phone is in the water, every second can be decisive in saving the gadget. Because even a drop of liquid that gets inside the device can cause a short circuit.

Step-by-step instructions will help you quickly take the necessary measures:

1. 1. You must immediately remove the phone from the water and turn it off. If the gadget was already turned off or was in “sleep” mode at the time of the fall, turning it on is strictly prohibited. You can check the device for functionality in no less than a day. Otherwise, a short circuit may occur, after which it will no longer be possible to revive the device at home.
2. 2. Now you should remove all foreign objects from the phone: case, protective film, SIM card, remove the headphones (if they were in the device connector at the time of the fall). The gadget should be kept level, in a horizontal position, without shaking it. Attempts to pour water out of the speakers and connectors by shaking only result in the liquid penetrating even deeper into the device.
3. 3. After turning off the device, you need to disassemble it as much as possible: remove the back cover, remove the battery, even remove the buttons (if the model is old). In this case, special care should be taken not to damage the internal device or touch the contacts. During disassembly, you need to try to remember where each part is located and what it is attached to, so that after all the manipulations you can correctly assemble the gadget yourself.
4. 4. All parts should be wiped dry with a napkin, paper towel, rags, rag - whatever is at hand. The main rule is that there should be no lint on any of the above items. After this, all metal contacts, cables, motherboard It is recommended to treat with alcohol. This will allow the moisture to evaporate faster and prevent further corrosion. Device with non-removable battery should be wiped very carefully with a dry, clean cloth in the areas where the connectors and other openings are located. You can twist paper strands and gently blot hard-to-reach areas. It is not recommended to wrap paper around sharp objects, such as the tip of a pen or pencil, as this is unsafe for small parts and is not beneficial.
5. 5. After all manipulations, the device must be left to dry naturally. This will take 24-48 hours. If possible, it is recommended to wait as long as possible. You cannot turn on the phone before the specified time in order to check its functionality, because even if the device is dry on top, the parts and contacts inside remain wet.

If your iPhone falls into water, after providing first aid, you should take it to a service center. This rule applies to all touch phones that cannot be disassembled. If you simply dry the device without treating the internal parts, there is a high risk that after some time it will fail. Water contains salts and minerals, which dry out and leave behind particles. They must be removed from the microcircuits to avoid further damage and corrosion.

Disassembling the device at home is very problematic, since the work will require special tools: a Phillips screwdriver, a plastic spatula, a vacuum suction cup for detaching the screen. Even if the necessary devices are at hand, there is a high risk of damaging an expensive device without the appropriate skills. Only specialists at the service center will be able to disassemble the device down to the last screw, assess the extent of damage and take the necessary measures.

How to dry your phone correctly?

Improvised objects and rather unusual means will help to effectively remove liquid:

• silica gel;
• cat litter;
• vacuum cleaner.

Vacuum cleaner

This is the easiest drying method, but it requires compliance with safety rules. Before the procedure, you need to make sure that the phone is not wet. It is strictly prohibited to suck up drops of water from the device with a vacuum cleaner to avoid electric shock. It is recommended to put a narrow nozzle on the hose and carefully treat the phone from all sides. You should not bring the hose too close to the device, as static electricity can damage the gadget.

It is strictly forbidden to dry your phone with a hairdryer, since the air directed at the device blows out the water droplets even more. inside. For the same reason, you cannot use a fan.

Rice or cat litter

Drying your phone with rice

Rice is an effective substitute that quickly absorbs moisture. For the procedure you will need a plastic container. It is necessary to fill it with cereal and immerse the phone and its parts in the container so that the rice completely covers the device. After this, the container with the phone must be tightly closed with a lid so that air does not penetrate there, and left for a day.

If you don't have rice, you can use granular cat litter. It absorbs moisture well, so the effect of the procedure will be similar to using rice.

Silica gel

Drying your phone with silica gel

Silicone bead bags are designed to absorb moisture. They are usually placed in shoe boxes. The product is easily recognized by the inscription “Silica Gel. Don't eat." Finding a lot of silica gel at home is not easy, but if you are lucky enough to find the right amount, then it is recommended to use it this method. The fact is that, unlike cereal or filler, bags do not leave small particles on the phone and absorb water much faster.

You need to take a bag with a sealed zipper, put the gadget with parts (battery, lid) in it, fill it with gel bags, close tightly and leave for a day.

Check connection

If the device does not work when turned on after complete drying, do not despair. A faulty battery may be to blame. Its performance can be checked on another device and, if necessary, replaced with a new one.

Another potential reason why your phone won't turn on is a low battery. You need to put the device on charge and when you turn it on, listen carefully to the operation of the device. Unusual noises and sounds may indicate that the device is not functioning properly.

A sensor will help determine whether water has entered the device. On touch phones there is a light circle or square near the battery. If it is white, it means that the liquid did not touch important parts, and if it is pink, then the water managed to affect the main elements.

When the phone works, but intermittently, it is recommended to take it to a service center or disassemble it yourself. Darkening on microcircuits or white plaque can be removed with a toothbrush. Brownish marks should be wiped with alcohol to prevent further corrosion.

A special kit for resuscitating wet gadgets, which can be found on the shelves of specialized stores, will help you quickly save your phone after falling into water.

If you are unable to resolve the problem yourself, it is recommended to contact a service center. It is quite possible that the breakdown is not so serious and for the correct functioning of the gadget one of the parts will need to be replaced. This will help you save money without buying new phone, and save important information, left in the old device.

Anyone can encounter a situation where their phone gets wet. The mobile device may fall into the sink or toilet. In most cases, this leads to a malfunction of the phone, which means the need to buy a new one. A few tips will help solve this problem.

First steps if your phone gets wet

With quick orientation and no panic, the mobile phone may remain in working condition. In some cases, independent actions are sufficient, without contacting a specialized service.

First of all, you need to immediately remove the device from the water. Headphone ports, charging ports and other openings quickly allow moisture to pass through. After removing the case, carefully wipe it with a paper or terry towel and remove the battery from the phone.

IMPORTANT! Be careful not to allow lint from towels or paper to clog the port passages.

SIM cards are quite resistant to damage, including being under water, but it also needs to be removed and wiped.

We perform similar actions with memory cards (if any). After disassembling the parts, you need to check the phone for damage when it is under water. Modern smartphones

equipped with a special white indicator. It is located in the battery connector. If the indicator turns pink or red, the device is seriously damaged. Repair work will be required.

After removal, place all components on a paper or terry towel. The device and its parts should be turned over periodically so that moisture that gets inside finds its way to the surface.

IMPORTANT! At the initial stage, these actions will be enough to dry and revive the mobile device.

If the phone was connected to a charger during the fall, it is strictly forbidden to remove it, since water is a conductor of current. You should seek help from a specialist.

Is it possible to dry your phone with a hairdryer?

When your phone falls into water, the first thought that comes to mind is to dry it with a hairdryer. However, such actions should be abandoned - you cannot dry the gadget with a hairdryer. Blowing with a hairdryer, even in a gentle mode, will worsen the situation. The incoming air disperses water droplets deeper into the housing. This causes the device to malfunction. After such repairs, you will need to purchase a new smartphone.

Exposure to hot air from a hair dryer can melt some of your phone's fragile components. Hot air will speed up the oxidation process of individual parts, increasing the likelihood of corrosion.

Conclusion: from using a hair dryer for drying mobile device should be refused.

What can you do if your phone gets wet?

After all components have been removed and disassembled, it is better to leave the device for a while. There are some ways you can use to speed up the drying process.

A few additional methods:

IMPORTANT! Placing a wet device in a microwave oven is strictly prohibited. Such actions will lead to permanent failure of the device. In addition, a phone placed inside the microwave chamber can cause an explosion.

If after preliminary repairs the smartphone still does not turn on, you need to check the functionality of the battery by connecting it to another device of the same model. If the battery works, the problem is in damaged microcircuits. Due to exposure to moisture, boards quickly corrode and oxidize. In this case, you will need to consult a specialist.

Without mobile phone the life of a modern person has become almost impossible. If you are not careful, the device may suffer from excessive exposure to moisture. Knowing the correct sequence of actions, you can fix the phone yourself.

Due to which the device stopped working, it can cause anxiety or even depression for many users. Still, not everyone will be pleased, due to their own oversight, to receive at their disposal an expensive brick that is not subject to warranty repair. However there is one effective way, which may help you restore the functionality of your gadget after water gets into the internal components.

You don't need any special tools for this. All you need to do is have a dry cloth and a bag of rice nearby. We will tell you in this article how this cereal will save your iPhone from moisture. So, you are sitting in the bath and listening to music from your iPhone, after which the phone suddenly takes the water procedure with you. Here is a list of what you should do immediately after you jump out of the bathtub and run out of the room in a panic with the device in your hands.

• Immediately turn off your iPhone by holding the Power button until the device turns off.
• Remove all covers and cases as they may also contain moisture.
• Immediately disconnect all cables and other accessories.
• If you see drops of water under protective film on the screen, remove it too.
• Dry your iPhone as best you can with available materials: towels, napkins, T-shirts, socks - whatever. Pay special attention to the power button, volume controls, volume mute button, speakers, microphones, and headphone jack.
• To clean open ports, use ear cotton swabs, but if you have a hair dryer, this would be ideal option. If you don't have either of these, a pencil can be used with a piece of fabric, such as a T-shirt, stretched across the tip.

Now that all the first preparations are done, it's time to entrust rice with the mission of restoring your iPhone to working order. It is worth noting that the rice should be regular and not “enriched”. We will explain below why this type of rice is not recommended. Another requirement is sealed packaging, such as a ziplock bag, as in the illustration below.

All you need to do is put the phone in a bag of rice, so that it is completely covered with grains of rice. After this, you need to close the bag tightly and be patient. Typically, it takes 36 hours for rice to completely absorb moisture. However, if you agree to wait two days, the result may be even better.

After the specified period, you can take the iPhone out of the package and, crossing your fingers, turn it on. As numerous experiments show, this method really helped many people bring the device back to life. As for the choice of rice, it is not recommended to use enriched rice because it leaves some white powder in the bag that can clog the ports and iPhone buttons. Regular rice does not have this property, so it is better to use it.

You should also remember that if you are planning to resurrect your iPhone a week after contact with water, then your chances will be close to zero. Ideally, such measures should be taken within 15 minutes after moisture enters the device. Every minute of delay reduces your chances of keeping your phone in its original condition.

By the way, the nature of the liquid that damaged your iPhone is also of certain importance. If we're talking about about salt water, the risk of losing a friend is higher, since this type of liquid has stronger corrosive properties. If you spill coffee or Coca-Cola on your phone, this is also more dangerous than plain water, since in addition to liquid, these drinks also leave some solids in the device. However, if you dry the device in time, there is still a chance of restoring its functionality.

But of course, the surest way to save yourself from the stress associated with the fact that your favorite gadget has malfunctioned is to be extra careful. If you really value your iPhone, just don't take it into the bath or pool with you. These few sweet minutes are hardly worth it to then go through all the unpleasant procedures described above.