Printing consumables at wholesale prices. Printing consumables at wholesale prices Xerox 3052 firmware

Fix firmware Xerox Phaser Phaser 3052

Price - 210 UAH. \ 500 rub. \ 7.9 USD

Model

Firmware version

Price

Phaser 3052

Phaser 3052NI

V3.50.01.05

210 UAH \ 500 rub. \ 7.9 USD

To order FIX firmware for Xerox Phaser 3052, find out the necessary information:

The exact model of the MFP ( see sticker on back panel)

MFP firmware version ( see in the configuration report line: Main Controller Board (MCB):)

Serial number MFP ( see in the report line: Machine Serial Number / Device serial number)

Cartridge chip CRUM number (see in the consumables report: Serial Number: CRUM- / Serial number: CRUM-)

Print Samsung Reports Xerox Phaser 3052

To print a Configuration report: Press and hold the [ STOP ] button for about 4 seconds (until the status indicator starts flashing quickly), release the button.

To print the Supplies Information report: Press and hold the [ STOP ] button for about 6 seconds (until the status indicator turns solid), then release the button.

Sample Configuration Report Xerox Phaser 3052

Sample Supplies Information report Xerox Phaser Phaser 3052

Xerox WorkCentre firmware instructions Phaser 3052

Stage 1. Flash the printer original firmware

Before FIX firmware, you must first flash the printer with the original firmware - Download and unpack the archive with the original firmware. Then enter the printer into forced download mode. To do this, with the printer turned off, press and hold the [STOP] button. Press and hold the [POWER] button, after ~1-2 seconds, release both buttons. Upon successful entry into forced mode, the status indicator should light up orange (the other indicators will also light up). Wait automatic installation forced mode drivers. Then use your mouse to transfer the firmware file Phaser_3052_V3.50.01.08.hd to usbprns2.exe. A black window with running dots will appear and close after a few seconds. After this, the printer will begin to flash. Wait until the printer reboots. After rebooting the printer, we proceed to the stages of FIX firmware.

Stage 2. Flash the printer with the first firmware fix file

The letter with the firmware comes with an archive containing three files (Two firmware files.hd and a file that launches the firmware usbprns2.exe)

In ready mode (there is no need to enter forced boot mode), use your mouse to transfer the first firmware file 1_Phaser-3052_V3.50.01.08.hd to usbprns2.exe

A black window with running dots will appear and close after a few seconds. After this, the device will begin to flash

Wait until the printer reboots. After rebooting the printer, we proceed to the next stage of the firmware.

Stage 3. Flash the printer with the second firmware fix file

Before this stage of the firmware, you need to put the printer into forced boot mode. N With the printer turned off, press and hold the [STOP] button. Press and hold the [POWER] buttonAfter ~1-2 seconds, release both buttons.Upon successful entry into forced mode, the status indicator should light up orange (the other indicators will also light up). Move the second FIX firmware file 2_FIX_NU_xxxxxxxxxx_Phaser-3052_V3.50.01.08.hd.hd to usbprns2.exe with your mouse . A black window with running dots will appear and close after a few seconds. After this, the device will begin to flash. Wait until the printer or MFP reboots.

Stage 4. Seal the chip contacts on the cartridge or remove the chi P

After the reboot, remove the chip and prevent the installation of other chips! The toner level will always show 100%.

We will be glad for your comment left after the printer firmware

Printer firmware instructions Xerox Phaser 3260DI, 3260DNI, 3052NI

To order the firmware you will need the following information:

  • Device model (written on the case);
  • Serial number (S/N);
  • CRUM cartridge chip;
  • Firmware version.

You will find this data by printing the "Configuration report" and " Consumables" (Supplies report).

Enter the data obtained from the reports into the “Order Form” in the right column of this page and click the “Order” button.

Printing reportsXerox Phaser 3260DI, 3260DNI, 3052NI

Printing the Configuration report:

In standby mode, press and hold the [ STOP ] button for about 4 seconds (until the status indicator starts flashing quickly), then release the button.

Printing the Supplies Information report:

Press and hold the [ STOP ] button for about 6 seconds (until the status indicator lights up continuously), then release the button.

If the blocking is complete, to print a report, replace the chip in the cartridge with an original working one.

Firmware versions and their compatibility

Firmware Phaser 3260DI, 3260DNI Phaser 3052NI

In the got archive

Instructions for flashing MFP firmware Phaser 3260DI, 3260DNI Phaser 3052NI

1 Flash the printer with original firmware

Download and unpack the archive with the original firmware (link to the archive with the original firmware at the bottom of the right column of this page). After this, put the printer into forced download mode. Wait for the forced mode drivers to install automatically. Then use your mouse to transfer the firmware file PH3260_V3.50.01.08.hd to usbprns2.exe. A black console window with running dots will appear and close after a few seconds. After this, the printer will begin to flash. Wait until the printer reboots. After rebooting the printer, proceed to installing the FIX firmware.

2. Flash the device with the first fix firmware file

In ready mode, use your mouse to transfer the first firmware file First_PH3260_V3.50.01.08.hd to usbprns2.exe

A console with running dots will appear, which will close after a few seconds. After this, the device will begin to flash

Wait for it to reboot. After the reboot, we proceed to the next stage of the firmware.

3. Flash the device with the second fix firmware file

Before this stage of the firmware, you need to put the printer into forced boot mode.

Use your mouse to transfer the second FIX firmware file FIX_NU_xxxxxxxxxx_PH3260_V3.50.01.08.hd to usbprns2.exe. A black window with running dots will appear and close after a few seconds. After this, the device will begin to flash. Wait until the printer or MFP reboots.

4 Seal the chip contacts on the cartridge or remove the chip

After the reboot, remove the chip and prevent the installation of other chips! The toner level will always show 100%.

Attention! For these MFP models, it is recommended to update the firmware from the ready mode.

Entering forced mode!

With the printer turned off, press and hold the [ STOP ] button. Press and hold the [POWER] button, after ~1-2 seconds, release both buttons. Upon successful entry into forced mode, the status indicator should light up orange (the other indicators will also light up).

After rebooting, the printer will already work without a chip on the cartridge.

Instructions for firmware Xerox WC-3025BI/V_BI (via USB)

Weaning off the Xerox Phaser 3052 chip.

Created 07/02/2015 10:32

Weaning off the Xerox Phaser 3052 chip.

New printers, new protection.

The Phaser 3052 printer has a number of advantages: it is silent in operation, reliable in operation and has high productivity. However, like all laser printers, its cartridge tends to become empty. To control this at the software level, the Phaser 3052 has a printed page counter, which, by checking the chip installed on the cartridge, blocks the operation of the cartridge after a certain mark, for example, 3000 pages. Thus, the printer advises users to purchase a new, always original, cartridge. Expensive consumables these days are the main source of income for companies producing printing equipment, so printers are equipped with refill protection, i.e. The program does not allow you to use the cartridge twice.

In this article we will look at a way to reprogram the device and allow users to save on expensive consumables. So the Phaser 3052 printer was no exception: moreover, the device itself is copy of Samsung SL-M2625, which can be easily flashed.
The process of flashing the Phaser 3052 firmware takes no more than 20 minutes, and is almost the only means of cheap printing on laser printer. Since this device is equipped software protection, then to make the printer “forget” the cartridges is to disassemble it and perform simple manipulations with its microcircuits responsible for counting pages.
In the first photo we see a brand new Phaser 3052: before starting work, make sure that the printer is “alive”, detected by the computer and printing reports. We advise you not to do it this procedure to avoid printer failure, which cannot always be repaired, and treat this article as information. Despite the simplicity of the procedure, any mistake can cost the printer its “life.”

Without removing the cartridge from the device, remove the side cover from the Phaser 3052 to get to the board. Disconnect all wires from the last one and remove it. back side we are not interested in the boards, because the necessary microcircuits are on the “front” side motherboard. As mentioned earlier, the Phaser 3052 printer is an absolute copy of the Samsung SL-M2625, therefore the same chips are used here: 25q128 and 24c256.


Using a soldering gun, we remove the above-mentioned microcircuits, install them on the programmer (in our case we used ChipProg48, but a Tryton programmer will do) and flash them.
Then we carefully return the microcircuits to the formatter board and perform the reverse procedure, i.e. We assemble the printer.
Important to remember!
After flashing, you must either seal or remove the chips from the cartridge! At the same time, you need to know that the manufacturing company prudently installed a chip on the drum cartridge and on the toner cartridge.
That's it, you can refill the cartridge

Printer firmware (firmware) - this is the installation software printer with a fixed code that resets the counter of printed pages and prevents the printer from being blocked.

Crypto protection (otherwise known as refill protection) installed in modern Samsung and Xerox devices, it counts the specified value using the formatter program code (shown in the picture), the number of pages printed, after which the printer is blocked and until you install a new cartridge or flash your printer, it will not work. The firmware of the device is done without opening or other actions aimed at violating the integrity, the printer is entered into service mode, after which FIX is “uploaded” via USB.
On the issue manufacturer's warranty. If you are worried that if the printer breaks down, you will not be able to contact the warranty workshop, we want to reassure you, let’s say your paper pickup roller is broken, you are going to take the printer or MFP to the service center, you can return firmware
firmware for the duration of repair in the warranty workshop of the manufacturer or seller. Many of our clients turn to our service under warranty and save a lot on refilling cartridges. Let's try to calculate the savings using the example of one printer... for example, Samsung ML-1660. Now many people are asking the question “What is printer firmware?”

An average-sized office buys a new cartridge (RUB 2,240) approximately once a month. Refilling the cartridge (350 rubles) is also required approximately once a month. The printer will last approximately 4 years or 48 months.
2240 rub. x 48 months = 107520 rub. This is the approximate cost of purchasing cartridges over 4 years (WOW!!!..........)
350 rub. cartridge refill x 48 months. =16800 rub. refueling cost for 4 years + 1000 rub. (firmware) = 17800 rub.
Thus the approximate saving in 4 years will be
89720 rubles, (of course, this is a rough calculation, during this time you will have to buy several cartridges since the physical resource is limited) and this is on 1 printer, but now think about it, don’t manufacturers of office equipment want to lose that kind of money from the users of their printers and MFPs? Of course, Samsung and Xerox are against refilling cartridges in any form, the fight against refillers continues as long as savings win, we’ll see what happens next.

Our services:

  • Approximate prices for services

    Name of works
    b/w f. A4
    up to 16 ppm
    b/w f. A3
    up to 16 ppm
    b/w f. A3
    16- 24 ppm
    b/w f. A3
    25 - 39 ppm
    b/w f. A3
    40-59 ppm
    Departure of an engineer within the Moscow Ring Road
    1000 1000 1000 1000 1000
    Departure of an engineer outside the Moscow Ring Road
    according to dogov. according to dogov. according to dogov. according to dogov. according to dogov.
    Diagnostics (paid if repair is refused)
    300 360 500 700 1000
    Prevention
    850 1020 1100 1450 1850
    Resetting error codes
    200 240 200 250 300
    Replacing Paper/Original Feed Parts
    750 900 950 1100 1200
    Repair of paper/original feed unit
    850 1020 1000 1200 1300
    Replacing paper transport parts
    700 840 800 900 1000
    Repair of paper transport unit
    800 960 900 1000 1100
    Replacing the photodrum and squeegee
    800 960 1100 1300 1600
    Replacing the Teflon shaft
    600 720 850 950 1050
    Replacing tefl bearings. shaft
    300 360 350 400 450
    Replacement rubber shaft
    650 780 700 950 1050
    Replacing rubber shaft bearings
    300 360 400 400 450
    Replacing the felt shaft
    400 480 450 450 500
    Replacing thermal film
    750 900 950 1200 1400
    Replacing the thermocouple
    750 900 950 1200 1400
    Repair of corona wire/charge roller
    400 480 500 600 800
    Replacing the developer
    500 600 550 600 700
    Removing electronic component (boards)
    250 300 300 500 650
    Repair of electronic component (boards)
    800 960 1000 1200 1400
    Removing the drive unit
    200 240 450 500 700
    Drive unit repair
    750 900 1000 1200 1500
    Mechanical repair
    700 840 900 1000 1300
    Replacing a Function Block
    700 840 900 1100 1300
    Scanner assembly repair
    800 960 1000 1200 1300
    Adjustment and calibration of the scanner assembly
    600 720 800 900 1100

Xerox Phaser 3052NI printer, which uses Laser b/w printing technology with a maximum paper size of A4, a print resolution of 600*600 and a print speed of up to 26 ppm. pages per minute, its use in small and medium-sized companies, at home, taking into account a small amount of printing, has proven itself excellent in terms of quality and the ability to refill cartridges.

The starter cartridge is designed for 600-700 pages (this is a starter - test cartridge), after which the Xerox Phaser 3052NI Printer indicates that the cartridge is running out of toner, and you need to buy and install a new one. But here you have a choice - buy a new cartridge or refill an empty one. If you choose the second option, a certain problem appears, namely: the cartridges for this printer have a built-in microcircuit (chip), it transmits to the device information about the remaining toner in the cartridge hopper. And if you are refilling a cartridge, it is not enough to fill it with toner; you need to remove the cryptographic protection from the chip (block the counting of printed pages).

Here again, there are two options for solving the problem - changing the chip in the cartridge or updating the printer firmware (changing the software) in the printer. Replacing a chip is expensive, since you have to change the chip every time you refill cartridges - this is the main disadvantage of replacement. The second one is much more profitable and less problematic than constantly replacing the chip - the Xerox Phaser 3052NI printer is reflashed once and for all.

Firmware for the Xerox Phaser 3052NI Printer is performed both in our workshop (1-2 hours) and in the client’s office. The customer must have a computer (laptop) with operating system Windows and Internet connection.

Make sure that the FIX version of the firmware available for ordering from the generator is compatible with the current printer firmware version.

Place your order at or Web generator Chipov.NET™ and download to HDD archive with firmware. Besides fix firmware printer Xerox Phaser 3260DI / 3260DNI / 3052NI, the archive also contains the program usbprns2.exe to send from OS Windows file firmware in USB port printer, and Text Document instructions.txt With detailed instructions according to the device firmware.

Printing a report

To print a report Сonfiguration:

In ready mode, press and hold [ STOP] near 4 seconds(until the status indicator starts flashing quickly), release the button.

To print a report Supplies Information:

Press and hold the [ button STOP] near 6 seconds
(until the status indicator lights up continuously), release the button.

It is possible to obtain full printer reports programmatically (as well as automatic receipt all data for ordering fix firmware), even if the printer is locked or the CRUM number is missing in the printed report!



Printing reports is possible from the utility Xerox Easy Printer Manager
(installed by default with the printer driver)


The necessary information for ordering fixed firmware is also available through the built-in web interface CentreWare Internet Services (see your printer user guide for details).

Sample Configuration report
Xerox Phaser 3260DI/DNI / 3052NI

Sample Supplies Information report
Xerox Phaser 3260DI/DNI / 3052NI

Entering forced firmware mode
Xerox Phaser 3260DI/DNI / 3052NI

With the printer turned off, press and hold the [ STOP ]

Press and hold the [ button POWER ],
After ~1-2 seconds, release both buttons.

Upon successful entry into forced mode, the status indicator should light up orange (the other indicators will also light up).




Top